Skip to main content

Linux CVE-2024-26802

MEDIUM
NULL Pointer Dereference (CWE-476)
2024-04-04 416baaa9-dc9f-4396-8d5f-8c081fb06d67
5.5
CVSS 3.1 · NVD
Share

Severity by source

NVD PRIMARY
5.5 MEDIUM
AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H

Primary rating from NVD · only source for this CVE.

CVSS VectorNVD

Attack Vector
Local
Attack Complexity
Low
Privileges Required
Low
User Interaction
None
Scope
Unchanged
Confidentiality
None
Integrity
None
Availability
High

Lifecycle Timeline

1
CVE Published
Apr 04, 2024 - 09:15 nvd
MEDIUM 5.5

DescriptionNVD

In the Linux kernel, the following vulnerability has been resolved:

stmmac: Clear variable when destroying workqueue

Currently when suspending driver and stopping workqueue it is checked whether workqueue is not NULL and if so, it is destroyed. Function destroy_workqueue() does drain queue and does clear variable, but it does not set workqueue variable to NULL. This can cause kernel/module panic if code attempts to clear workqueue that was not initialized.

This scenario is possible when resuming suspended driver in stmmac_resume(), because there is no handling for failed stmmac_hw_setup(), which can fail and return if DMA engine has failed to initialize, and workqueue is initialized after DMA engine. Should DMA engine fail to initialize, resume will proceed normally, but interface won't work and TX queue will eventually timeout, causing 'Reset adapter' error. This then does destroy workqueue during reset process. And since workqueue is initialized after DMA engine and can be skipped, it will cause kernel/module panic.

To secure against this possible crash, set workqueue variable to NULL when destroying workqueue.

Log/backtrace from crash goes as follows: [88.031977]------------[ cut here ]------------ [88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out [88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398 <Skipping backtrace for watchdog timeout> [88.032251]---[ end trace e70de432e4d5c2c0 ]--- [88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter. [88.036359]------------[ cut here ]------------ [88.036519]Call trace: [88.036523] flush_workqueue+0x3e4/0x430 [88.036528] drain_workqueue+0xc4/0x160 [88.036533] destroy_workqueue+0x40/0x270 [88.036537] stmmac_fpe_stop_wq+0x4c/0x70 [88.036541] stmmac_release+0x278/0x280 [88.036546] __dev_close_many+0xcc/0x158 [88.036551] dev_close_many+0xbc/0x190 [88.036555] dev_close.part.0+0x70/0xc0 [88.036560] dev_close+0x24/0x30 [88.036564] stmmac_service_task+0x110/0x140 [88.036569] process_one_work+0x1d8/0x4a0 [88.036573] worker_thread+0x54/0x408 [88.036578] kthread+0x164/0x170 [88.036583] ret_from_fork+0x10/0x20 [88.036588]---[ end trace e70de432e4d5c2c1 ]--- [88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004

AnalysisAI

In the Linux kernel, the following vulnerability has been resolved: stmmac: Clear variable when destroying workqueue Currently when suspending driver and stopping workqueue it is checked whether. Rated medium severity (CVSS 5.5), this vulnerability is low attack complexity. This NULL Pointer Dereference vulnerability could allow attackers to crash the application by dereferencing a null pointer.

Technical ContextAI

This vulnerability is classified as NULL Pointer Dereference (CWE-476), which allows attackers to crash the application by dereferencing a null pointer. In the Linux kernel, the following vulnerability has been resolved: stmmac: Clear variable when destroying workqueue Currently when suspending driver and stopping workqueue it is checked whether workqueue is not NULL and if so, it is destroyed. Function destroy_workqueue() does drain queue and does clear variable, but it does not set workqueue variable to NULL. This can cause kernel/module panic if code attempts to clear workqueue that was not initialized. This scenario is possible when resuming suspended driver in stmmac_resume(), because there is no handling for failed stmmac_hw_setup(), which can fail and return if DMA engine has failed to initialize, and workqueue is initialized after DMA engine. Should DMA engine fail to initialize, resume will proceed normally, but interface won't work and TX queue will eventually timeout, causing 'Reset adapter' error. This then does destroy workqueue during reset process. And since workqueue is initialized after DMA engine and can be skipped, it will cause kernel/module panic. To secure against this possible crash, set workqueue variable to NULL when destroying workqueue. Log/backtrace from crash goes as follows: [88.031977]------------[ cut here ]------------ [88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out [88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398 <Skipping backtrace for watchdog timeout> [88.032251]---[ end trace e70de432e4d5c2c0 ]--- [88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter. [88.036359]------------[ cut here ]------------ [88.036519]Call trace: [88.036523] flush_workqueue+0x3e4/0x430 [88.036528] drain_workqueue+0xc4/0x160 [88.036533] destroy_workqueue+0x40/0x270 [88.036537] stmmac_fpe_stop_wq+0x4c/0x70 [88.036541] stmmac_release+0x278/0x280 [88.036546] __dev_close_many+0xcc/0x158 [88.036551] dev_close_many+0xbc/0x190 [88.036555] dev_close.part.0+0x70/0xc0 [88.036560] dev_close+0x24/0x30 [88.036564] stmmac_service_task+0x110/0x140 [88.036569] process_one_work+0x1d8/0x4a0 [88.036573] worker_thread+0x54/0x408 [88.036578] kthread+0x164/0x170 [88.036583] ret_from_fork+0x10/0x20 [88.036588]---[ end trace e70de432e4d5c2c1 ]--- [88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004 Affected products include: Linux Linux Kernel.

RemediationAI

A vendor patch is available. Apply the latest security update as soon as possible. Check pointers before dereferencing. Use static analysis tools to detect null pointer paths.

Share

CVE-2024-26802 vulnerability details – vuln.today

This site uses cookies essential for authentication and security. No tracking or analytics cookies are used. Privacy Policy