In the Linux kernel, the following vulnerability has been resolved: gpio: mxc: fix race between chained IRQ handler install and probe completion mxc_update_irq_chained_handler() is called before the IRQ domain, the generic IRQ chip, and the port list entry are set up. If an interrupt arrives in that window: - mx3_gpio_irq_handler() calls generic_handle_domain_irq() with port->domain still NULL. - mx2_gpio_irq_handler() walks mxc_gpio_ports, but the port has not been added to the list yet. Additionally, if any of the subsequent probe steps (gpio_generic_chip_init(), devm_gpiochip_add_data(), irq_domain_create_legacy(), or mxc_gpio_init_gc()) fail, the error paths never unregister the chained handler, leaving a dangling handler that points at freed memory. Move the handler installation after all its dependencies are ready and after list_add_tail(), so the handler is never live while the data structures it touches are incomplete, and is never installed if probe fails.
In the Linux kernel, the following vulnerability has been resolved: net: stmmac: dwmac1000: clear the RGMII status interrupt Since commit 2e2c878a3141 ("net: stmmac: remove SGMII/RGMII/SMII interrupt handling") nothing on the RGMII path reads GMAC_RGSMIIIS, so RGSMIIIS stays pending behind GMAC_INT_MASK from the first link change on. stmmac_resume() resets the MAC in stmmac_hw_setup(); the reset sets GMAC_INT_MASK to 0 until dwmac1000_core_init() writes the mask again, and the pending status storms the line: dwmac_dma_interrupt: unexpected status 04000000 A register dump at the first message on ODROID-HC4 showed it: core int_status 00000001 int_mask 00000000 pmt 00000000 rgsmiiis 0000000d When the resume thread runs on the CPU that takes the MAC interrupt, the storm starves it: a soft lockup, then a watchdog reset or a hang. Read GMAC_RGSMIIIS in dwmac1000_irq_status() when the status is not masked, as the driver did before 2e2c878a3141; the read clears it. Wake-on-LAN resume from s2idle with the resume thread and the MAC interrupt on one CPU: Helios64 (dwmac-rk), 7.3-rc6, soft-locked in 3 of 3 resumes without a fix and in 0 of 10 with this patch; it ran with an out-of-tree dwmac-rk change that keeps the GMAC powered across suspend. ODROID-HC4 (dwmac-meson8b): 0 of 10 with this patch, 2 of 2 without a fix on a 7.3-rc5 build. irq_rgmii_n went up by one per resume.
In the Linux kernel, the following vulnerability has been resolved: perf: Fix perf_pmu_migrate_context() leaving events behind __perf_pmu_remove() walks the group leaders of a CPU and PMU with perf_event_groups_for_cpu_pmu(), removing each one as it goes. perf_remove_from_context() takes the leader out of the groups rbtree, after which rb_next() on that node returns NULL, prematurely ending the walk. Other groups stay behind in the source context. On CPU hotplug, they are then torn down with the dying CPU. They keep running until teardown, while the PMU's interrupt and migrated events are on a new CPU, which drivers rely on never happening. Walk ctx->event_list instead and pick out the PMU's events by their pmu_ctx.
In the Linux kernel, the following vulnerability has been resolved: x86/insn-eval: Fix shadowed segment index in get_seg_reg_override_idx() Commit 45e1dccc0653 ("x86/insn: Simplify for_each_insn_prefix()") made for_each_insn_prefix() declare its own loop counter named idx. get_seg_reg_override_idx() keeps its result in a local of the same name, so the assignments in the loop body now write the loop counter: - the function always returns INAT_SEG_REG_DEFAULT, so FS and GS overrides are ignored; - a CS override sets the counter to INAT_SEG_REG_CS (2), the increment makes it 3, and prefixes.bytes[3] holds the last prefix, 0x2e again, so the loop never terminates. The UMIP emulation reaches this from the #GP handler for user space: an SGDT, SIDT or SMSW with a memory operand and a CS prefix leaves the task spinning in the kernel, never returning to user space, with a SIGKILL that is never delivered. Any user can thus tie up CPUs until reboot. With an FS or GS prefix, the emulated result is written to the wrong address. Rename the internal macro iterator variable. [ Lukas' original patch renamed the use site, I changed it to rename the iterator in the macro instead, but left Lukas' commit message and authorship - Linus ]
In the Linux kernel, the following vulnerability has been resolved: firewire: core: fix race condition in split transaction handling For a split transaction, either fw_core_handle_response() or split_transaction_timeout_callback() may manipulate the same transaction entry in the pending transaction list. The return value of timer_delete() is used to determine which function handles the entry. If the transaction is a split transaction and timer_delete() returns zero, the timeout callback may already be running. In this case, the response handler must leave the entry in the list for the timeout callback to remove. A previous code refactoring broke this behavior, introducing a race condition in which both functions could process the same transaction. This could lead to a use-after-free on the transaction initiator side. Fix the regression by ensuring that the response handler does not process the transaction when timer_delete() returns zero. The timeout callback is responsible for removing the entry from the pending transaction list.
In the Linux kernel, the following vulnerability has been resolved: accel/rocket: search every core slot when a core is removed rocket_remove() decrements rdev->num_cores for each core it removes, while find_core_for_dev() searches slots 0 to num_cores - 1. Unbinding the cores in the order they were bound therefore loses the last one: by the time it is removed the search range has already shrunk past its slot, so find_core_for_dev() returns -1 and rocket_remove() gives up without doing anything. num_cores never reaches zero, rocket_device_fini() never runs, and the file-scoped rdev keeps pointing at a device that is going away. Binding the cores again starts from that stale count, because rocket_probe() takes rdev->num_cores as the slot to fill. On an RK3588, which describes three cores, the second round lands on slots 1, 2 and 3 while rdev->cores was allocated with room for three: rocket fdab0000.npu: Rockchip NPU core 1 version: 1179210309 rocket fdac0000.npu: Rockchip NPU core 2 version: 1179210309 rocket fdad0000.npu: Rockchip NPU core 3 version: 1179210309 The write to rdev->cores[3] is past the end of the array. Nothing in tree reads the core array often enough to notice, so the overrun is silent today. It turned up while testing a devfreq series on top of this, where a worker walks every core a few times a second, and UBSAN caught the first bool it read out of the overrun entry: UBSAN: invalid-load in drivers/accel/rocket/rocket_devfreq.c:47:10 load of value 5 is not a valid value for type '_Bool' Workqueue: devfreq_wq devfreq_monitor Record how many slots were allocated and search all of them. Every core is then found on removal, num_cores reaches zero, the device is torn down and a later bind starts from a clean rdev. This does not make unbinding a single core out of several work. probe still takes num_cores as the slot to fill, so rebinding one core while its siblings stay bound would write over a slot that is already in use, and rocket_open() still reaches for cores[0] whether or not anything is there. Both of those want more thought than a fix should carry. Found by unbinding and rebinding all three cores on an Orange Pi 5 Plus. With this applied, 25 unbind/rebind rounds and 5 module unload/reload rounds run clean there: the cores land in slots 0, 1 and 2 every time, whichever order they are bound in, and the shared supply goes back to a single user after each round.
In the Linux kernel, the following vulnerability has been resolved: accel/rocket: search every core slot when looking up a scheduler sched_to_core() walks rdev->cores[] up to rdev->num_cores, and rocket_remove() decrements num_cores for every core it removes. Unbind a core that is not the last one and the cores behind it fall outside the search, so sched_to_core() returns NULL for a core that is still bound and still running jobs. Neither caller checks the result: rocket_job_run(): rocket_fence_create(core), core->dev rocket_job_timedout(): dev_err(core->dev, "NPU job timed out") Unbinding the middle core of the three on an RK3588 while three clients are submitting to all of them faults twice, once from the surviving core's job queue and once from its reset work: KASAN: null-ptr-deref in range [0x0000000000000220-0x0000000000000227] Workqueue: fdad0000.npu drm_sched_run_job_work [gpu_sched] pc : rocket_job_run+0x234/0x838 [rocket] Call trace: rocket_job_run+0x234/0x838 [rocket] drm_sched_run_job_work+0x2cc/0xad8 [gpu_sched] process_one_work+0x640/0x14f0 KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] Workqueue: rocket-reset-2 drm_sched_job_timedout [gpu_sched] pc : rocket_job_timedout+0xf0/0x1e0 [rocket] Call trace: rocket_job_timedout+0xf0/0x1e0 [rocket] drm_sched_job_timedout+0x188/0x6a0 [gpu_sched] Both are the third core: the workqueue names are its device and its core->index, and it was left at slot 2 while num_cores had dropped to 2. Search all the slots that were allocated, the way find_core_for_dev() now does. A core that is still bound is then found, and the two callers get the pointer they already assume they have. This does not make unbinding one core out of several safe. An open client keeps an entity pointing at the scheduler of the core that went away: drm_sched reports it as not ready for every job that lands on it, and the client waits in dma_fence_default_wait for a fence that will never signal. Stopping the NULL dereference is what belongs in a fix; the rest wants more thought.
In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc4-topology: Fix shift-out-of-bounds for aggregated ALH capture When ch_count is smaller than blob->alh_cfg.device_count (e.g. a mono capture stream, such as a SmartMic, aggregated across multiple SDW links), step = ch_count / blob->alh_cfg.device_count truncates to 0. The subsequent GENMASK(step - 1, 0) then underflows step - 1 (u32) to UINT_MAX, causing GENMASK()'s internal shift to use an out-of-bounds exponent: UBSAN: shift-out-of-bounds in sound/soc/sof/ipc4-topology.c:2363:13 shift exponent 18446744069414584384 is too large for 64-bit type 'long unsigned int' Treat ch_count < device_count the same way as the existing "channels equal to output reference channels" case: apply the same ch_mask to every aggregated device instead of trying to split channels that can't be evenly divided.
In the Linux kernel, the following vulnerability has been resolved: autofs: ignore notification errors from a replaced pipe autofs_notify_daemon() takes a reference to the current notification pipe under wq_mutex, then drops the mutex before writing the request. The write can block while the daemon enters catatonic mode and installs a replacement pipe. If the old pipe's reader is then closed, the delayed write returns -EPIPE and the generic error path enters catatonic mode again. That transition acts on the current superblock state, closes the replacement pipe, and releases the new daemon generation's wait queues. Only enter catatonic mode when the pipe which failed is still the current pipe. Factor the already-locked transition so the identity check and state change are atomic with respect to another replacement. This was reproduced on v7.3-rc5-337-gff47652a4b66c in a local QEMU guest. An unprivileged UID 65534 lookup filled the old packet pipe before a normal CATATONIC/SETPIPEFD restart. On the unmodified kernel, the new pipe received HUP and both a pending victim lookup and a later lookup failed with ENOENT in two out of two fresh-mount runs. With this change, the new pipe remained active, received an intact 304-byte request, and both victim lookups completed in two out of two runs. Normal lookup and restart-without-a-blocked-writer controls passed. No KASAN, oops, refcount, or lock diagnostic was observed. A source reproducer and complete local logs are available privately on request. The demonstrated impact is limited to denial of a shared autofs service during a legitimate daemon restart. No memory corruption, information leak, privilege escalation, or code execution primitive was observed.
In the Linux kernel, the following vulnerability has been resolved: unicode: free the map after a grace period generic_ci_d_hash() and generic_ci_d_compare() read sb->s_encoding and dereference the unicode map while a pathwalk in rcu mode holds nothing but rcu_read_lock(). The filesystems that use them, ext4, f2fs and tmpfs, drop the map with utf8_unload() from ->put_super(), which runs when the last reference to the mount goes away. A lookup that is still inside such a filesystem at that point reads a freed map. With a pathwalk held up in utf8_casefold_hash() while the last reference to a casefolded tmpfs goes away: BUG: KASAN: slab-use-after-free in utf8nlookup+0x74c/0x950 Read of size 8 at addr ff110001030fe658 by task walker/98 Call Trace: <TASK> utf8nlookup+0x74c/0x950 utf8byte+0x160/0x1560 utf8_casefold_hash+0x167/0x230 generic_ci_d_hash+0xdd/0x1c0 link_path_walk+0x11ad/0x1d30 path_lookupat+0x63/0xb00 filename_lookup+0x1f1/0x5b0 vfs_statx+0xd7/0x3b0 [...] Allocated by task 94: __kmalloc_cache_noprof+0x249/0x560 utf8_load+0x4e/0x570 shmem_parse_opt_casefold.isra.0+0x92/0x270 [...] Freed by task 97: kfree+0x1db/0x5b0 shmem_put_super+0x72/0x170 generic_shutdown_super+0x14c/0x530 kill_anon_super+0x3a/0x60 deactivate_locked_super+0x9c/0xf0 cleanup_mnt+0x9f/0x130 So far that has been hard to hit. umount(2) waits for a grace period in namespace_unlock() before it drops the mount, so only a mount whose last reference goes away elsewhere, like the close of a file or a chdir out of a lazily unmounted directory, can race a walker. So it is reachable. Delay the free until a grace period has passed. The map and the data table it holds a reference to then outlive any pathwalk that found the superblock before the mount went away. The reference on the data table module is dropped from the rcu callback as well. utf8-core is built in whenever CONFIG_UNICODE is set, so there is no module exit that would have to wait for the callbacks. Overlayfs points the s_encoding of an overlay at the map of its first layer without taking a reference of its own. That stays correct. The layer is held by the overlay, so its map is dropped only after the overlay is gone.
In the Linux kernel, the following vulnerability has been resolved: watch_queue: Fix note pool publication race in watch_queue_set_size() There is a race between watch_queue_set_size() and post_one_notification(). watch_queue_set_size() publishes wqueue->notes, notes_bitmap, nr_pages and nr_notes with plain stores, and post_one_notification() reads them with plain loads under a different lock, so nothing orders the four stores against the poster's loads: depending on the build, notes can be stored last (gcc 14 on x86-64 does this). Since keyctl_watch_key() lets a watch attach to a queue before it is sized, post_one_notification() can already be running on another CPU at that moment: it reads nr_notes > 0, passes its bounds check, and then reads notes while it is still NULL, dereferencing notes[0]. An unprivileged user triggers this reliably by watching one of its own keys through a notification pipe and racing ioctl(IOC_WATCH_QUEUE_SET_SIZE) on that pipe against keyctl(KEYCTL_SETPERM) on the key from another CPU, triggering: BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:post_one_notification.isra.0+0xa2/0x1e0 Call Trace: __post_watch_notification+0x148/0x180 keyctl_setperm_key+0x119/0x130 do_syscall_64+0x108/0x4c0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Kernel panic - not syncing: Fatal exception in interrupt Fix this by publishing nr_notes last with smp_store_release(), and by reading it once with smp_load_acquire() in post_one_notification() before the bitmap and the page array are touched. A poster that observes a non-zero nr_notes then also observes the pool behind it; one that observes zero drops the notification as before.
In the Linux kernel, the following vulnerability has been resolved: x86/kvm: Don't consume async #PF flags on a kernel #PF in NMI context An async #PF "page not present" event arrives through the #PF vector, and its reason sits in the per-CPU apf_reason.flags until __kvm_handle_async_pf() reads and clears it. If an NMI arrives after the event is injected and before the #PF handler reads the flags, and the NMI handler itself takes a #PF, that fault reads and clears the flags belonging to the #PF it interrupted. It then finds interrupts disabled in the NMI context it interrupted, and panics: Kernel panic - not syncing: Host injected async #PF in interrupt disabled region Call Trace: <NMI> panic+0x52/0x60 __kvm_handle_async_pf+0xb0/0xb0 exc_page_fault+0x71/0xb0 asm_exc_page_fault+0x27/0x30 RIP: 0010:__get_user_nocheck_8+0x6/0x20 perf_callchain_user+0x147/0x1a0 get_perf_callchain+0x12d/0x1c0 ... perf_event_nmi_handler+0x26/0x50 exc_nmi+0xe8/0x110 RIP: 0010:asm_exc_page_fault+0x0/0x30 </NMI> The last RIP line shows the NMI landing on the first instruction of the #PF entry. perf with user call chains takes such a fault: the sampling NMI walks the user stack with __get_user(), which faults when a saved frame pointer is not a valid user address or the walk runs off the top of the stack. The same window exists when KVM, running as an L1 hypervisor with DELIVERY_AS_PF_VMEXIT, reads the flags itself after a #PF VM-exit. The NMI entry code saves and restores CR2 for this nesting, but not the async #PF reason. Andy Lutomirski described the race, with perf as the example, when async #PF delivery was reworked in 2020 [1]. Saving and clearing the flags across the NMI, next to CR2, was discussed there but not merged. Since that rework, Linux has stopped setting KVM_ASYNC_PF_SEND_ALWAYS, so the host delivers "page not present" only for user mode faults and a kernel-mode fault in NMI context (including kernel-mode #MC and #DB) cannot be an async page fault. In that case, return without touching the flags so that the interrupted handler finds them intact. Tested on v7.3-rc5 in a 4-vCPU, 2 GiB guest restored from a snapshot whose memory is served on demand through userfaultfd, so that reading it back takes async #PFs, while every thread samples hardware cycles with user call chains and points its frame pointer at an unmapped page. Without this patch the guest panicked as above in 3 of 3 runs. With it, the guest survived 3 of 3 runs of 60 seconds, and the host counted 148,441 to 153,334 kvm_async_pf_not_present events in the first 20 seconds of each. On 6.18.50 the results were the same: the guest panicked without the patch and survived with it.
In the Linux kernel, the following vulnerability has been resolved: KVM: SEV: Fix page dirtying in sev_gmem_post_populate() set_page_dirty() requires that the caller holds some kind of lock to ensure that the page's mapping does not concurrently go away. That is not the case for a random page we got from get_user_pages_fast(), so use set_page_dirty_lock(). [sean: tag for stable]
In the Linux kernel, the following vulnerability has been resolved: KVM: nVMX: Reset MMU back to the root MMU if loading L2 state fails for !VM-Entry Reset the vCPU's MMU pointer back to the root MMU if loading L2 state fails in the "not from VM-Entry" case, i.e. when emulating RSM or handling KVM_SET_NESTED_STATE. Failure to unwind the MMU pointer results in KVM trying to run L1 with a nested MMU, and is especially problematic if the vCPU manages to free its nested state before the VM crashes. Constructing the root for a nested EPT MMU goes through vmcs12, which is dynamically allocated/freed when nVMX is enabled/disabled. And so if the nested state is freed with the MMU still pointing at the nested MMU, KVM will hit a NULL pointer deref when attempting to get L1=>L2 EPTP. BUG: kernel NULL pointer dereference, address: 0000000000000078 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 114a2d067 P4D 111743067 PUD 11141f067 PMD 0 Oops: Oops: 0000 [#1] SMP CPU: 20 UID: 1000 PID: 1272 Comm: nested_tdp_faul Not tainted 7.3.0-rc4-8c89f11d1a99b-sink-vm #1914 PREEMPTLAZY Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:nested_ept_get_eptp+0xb/0x10 [kvm_intel] Call Trace: <TASK> kvm_mmu_load+0xcd/0x870 [kvm] kvm_arch_vcpu_ioctl_run+0x18f5/0x1f80 [kvm] kvm_vcpu_ioctl+0x2c7/0x970 [kvm] __x64_sys_ioctl+0x90/0xd0 do_syscall_64+0x9c/0x4d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x47491b </TASK> Modules linked in: kvm_intel kvm irqbypass CR2: 0000000000000078 ---[ end trace 0000000000000000 ]--- RIP: 0010:nested_ept_get_eptp+0xb/0x10 [kvm_intel] [sean: write changelog]
In the Linux kernel, the following vulnerability has been resolved: fsnotify: prevent mark additions during connector teardown fsnotify_destroy_marks() keeps a reference to its current mark while it drops conn->lock to destroy the mark. This stabilizes the forward-walk cursor, but does not prevent a new mark from being inserted before it. For example, an inotify watch re-added after IN_IGNORED sorts before the old, detached mark for the same group. The walk can miss the replacement and then detach the entire connector from the object. The replacement is still on its group's marks_list and, for inotify, in the watch IDR. The group mutex no longer protects the connector's object from disappearing. An unprivileged fdinfo read racing the final detach can consequently call igrab(NULL): BUG: KASAN: null-ptr-deref in igrab+0x24/0x100 Write of size 4 at addr 0000000000000148 Call Trace: igrab+0x24/0x100 inotify_show_fdinfo+0x1dc/0x5e0 seq_show+0x397/0x690 Set a DESTROYING flag under conn->lock before starting the walk, and reject new marks on that connector with -ENOENT. The existing add-mark error paths undo the temporary group-list entry and the backend's watch allocation. Do not wait for teardown while holding the group mutex, which the destroyer needs. Once the old connector is detached, an add can install a fresh connector as before. This closes the insertion race for all object types using the common connector teardown, without changing the mark reference or SRCU lifetime rules.
In the Linux kernel, the following vulnerability has been resolved: ext4: free the sbi after a grace period ext4_get_link() follows a symlink that keeps its target in a data block in rcu pathwalk mode with ext4_getblk(EXT4_GET_BLOCKS_CACHED_NOWAIT). That reads s_mount_state in the ASSERT() of ext4_getblk() and again in ext4_es_lookup_extent(), and the lookup bumps the extent status hit or miss counter, all through sb->s_fs_info. ext4_put_super() destroys those counters, clears sb->s_fs_info and frees the sbi without waiting for a grace period. A pathwalk that is still in ext4_get_link() when the last reference to the mount goes away then dereferences a NULL s_fs_info, the freed sbi or the destroyed percpu counters. With a pathwalk held up in ext4_get_link() while the last reference goes away: KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af] RIP: 0010:ext4_getblk+0xf0/0x640 Call Trace: <TASK> ext4_get_link+0x26c/0x410 pick_link+0xf96/0x1780 step_into_slowpath+0x9b8/0x1250 path_lookupat+0x484/0xb00 filename_lookup+0x1f1/0x5b0 vfs_statx+0xd7/0x3b0 vfs_fstatat+0x4d/0x90 __do_sys_newfstatat+0xa0/0x100 do_syscall_64+0x10e/0x5e0 entry_SYSCALL_64_after_hwframe+0x77/0x7f So far that has been hard to hit. umount(2) waits for a grace period in namespace_unlock() before it drops the mount, so only a mount whose last reference goes away elsewhere, like the close of a file or a chdir out of a lazily unmounted directory, can race a walker. Keep sb->s_fs_info and free the sbi together with the extent status counters after a grace period. Split the counters out of ext4_es_unregister_shrinker() for that. The shrinker still gets wasted in ext4_put_super(), the counters go with the sbi.
In the Linux kernel, the following vulnerability has been resolved: eventfs: Free the eventfs_inode after an rcu grace period too tracefs_d_revalidate() reads ->is_freed of the eventfs_inode that dentry->d_fsdata points to, and ->d_revalidate() is called in rcu pathwalk mode with nothing but rcu_read_lock() held. The dentry itself stays around for such a walker, but tracefs_d_release() drops its reference to the eventfs_inode when the dentry is killed, and release_ei() then frees it after a grace period of eventfs_srcu. An SRCU grace period doesn't wait for rcu_read_lock() sections, so the walker can read an eventfs_inode that is already gone. With a pathwalk held up in tracefs_d_revalidate() while the dentry goes away: BUG: KASAN: slab-use-after-free in tracefs_d_revalidate+0x76/0x90 Read of size 1 at addr ff1100010152d8d0 by task walker/97 Call Trace: <TASK> tracefs_d_revalidate+0x76/0x90 lookup_fast+0x320/0x640 path_lookupat+0x160/0xb00 filename_lookup+0x1f1/0x5b0 vfs_statx+0xd7/0x3b0 vfs_fstatat+0x4d/0x90 __do_sys_newfstatat+0xa0/0x100 do_syscall_64+0x10e/0x5e0 entry_SYSCALL_64_after_hwframe+0x77/0x7f [...] Allocated by task 1: __kmalloc_cache_noprof+0x249/0x560 eventfs_create_dir+0x7a/0x590 event_create_dir+0x2fb/0xcf0 trace_add_event_call+0xbf/0x150 [...] Freed by task 11: kfree+0x1db/0x5b0 srcu_invoke_callbacks+0x3a3/0x620 process_one_work+0x937/0x1810 worker_thread+0x4f1/0xd60 Before commit 8e556432477e ("eventfs: Use SRCU for freeing eventfs_inodes") release_ei() used call_rcu(), which covered the walker, while eventfs_iterate() needs the SRCU grace period. Wait for both and chain call_rcu() from the SRCU callback.
In the Linux kernel, the following vulnerability has been resolved: ipc: drop the mqueue mount with kern_unmount() on setup failure mq_init_ns() creates the mqueue mount with fc_mount_longterm(), so its ->mnt_ns is MNT_NS_INTERNAL. When setting up the mqueue or ipc sysctls or msg_init_ns() fails afterwards, create_ipc_ns() drops it with a plain mntput(). With ->mnt_ns set that takes the fast path of mntput_no_expire(). The count drops to zero and nothing ever kills the mount, so the mount and the mqueue superblock are leaked. Commit dc55e35f9e81 ("ipc: Store mqueue sysctls in the ipc namespace") added the first failure path after mq_init_ns() and never dropped the mount. Commit 7229d74e5e8c ("ipc: create_ipc_ns: drop mqueue mount on sysctl setup failure") tried to fix that with a mntput() but that doesn't help for a long-term mount. Use kern_unmount(). free_ipc() open-codes the same thing for a namespace that made it.
In the Linux kernel, the following vulnerability has been resolved: ntfs3: free the sbi after a grace period If the "nocase" mount option ntfs3 uses custom hash and dentry compare functions. Both access ntfs3 superblock private information in rcu pathwalk. ntfs_put_super() and ntfs3_kill_sb() drop the info without any rcu delay. A lookup that's still inside the filesystem when the last reference to the mount is dropped causes a UAF. With a pathwalk held up in ntfs_d_hash() while the last reference to the mount goes away: BUG: KASAN: slab-use-after-free in ntfs_nls_to_utf16+0x752/0x940 Read of size 8 at addr ff1100010453c850 by task walker/99 Call Trace: <TASK> ntfs_nls_to_utf16+0x752/0x940 ntfs_d_hash+0x22b/0x500 link_path_walk+0x11ad/0x1d30 path_lookupat+0x63/0xb00 filename_lookup+0x1f1/0x5b0 vfs_statx+0xd7/0x3b0 [...] Allocated by task 95: __kmalloc_cache_noprof+0x249/0x560 ntfs_init_fs_context+0x2db/0x5a0 alloc_fs_context+0x52e/0xc70 [...] Freed by task 98: kfree+0x1db/0x5b0 deactivate_locked_super+0x9c/0xf0 cleanup_mnt+0x9f/0x130 task_work_run+0x131/0x250 The bug is currently masked by the grace period in namespace_unlock() for umount(2). Keep the necessary information until the filesystem private info is freed and free it with an rcu delay. ntfs3_free_sbi() now runs from an rcu callback and drops the upcase table via ntfs_put_shared(). So switch s_shared_lock over to spin_lock_bh(). Otherwise the callback can deadlock against a task holding the lock on the same cpu.
In the Linux kernel, the following vulnerability has been resolved: namespace: a mount that copy_tree() leaves out can't take over a lock Since commit c62a4766937e ("move_mount: transfer MNT_LOCKED") a mount can be moved beneath a locked mount. The lock moves from the old cover to the new mount which takes over the job of hiding what's under it and the old cover can be unmounted. That works as long as the new mount stays. But the caller picks the new mount and copy_tree() leaves a mount of a mount namespace file out of every copy made without CL_COPY_MNT_NS_FILE, together with everything mounted on it, and never looks at MNT_LOCKED. unshare(CLONE_NEWNS) and mount propagation make such copies. So a task that is root in its own user namespace gets rid of a locked cover on a file without a race and without touching the filesystem below it. It makes a child with a mount namespace of its own, binds the child's /proc/<pid>/ns/mnt beneath the cover with MOVE_MOUNT_BENEATH, which hands the lock to that bind, and calls unshare(CLONE_NEWNS). The new mount namespace has nothing on the file. That's the usual way to mask a single file, a bind of /dev/null or of an empty file. With a bind of an ordinary file the file stays covered. copy_tree() already refuses to leave out a locked unbindable mount with -EPERM since commit df7342b24018 ("mount: Don't allow copying MNT_UNBINDABLE|MNT_LOCKED mounts"). Do the same for a locked mount of a mount namespace file. That also covers a tree copied with CL_COPY_MNT_NS_FILE and attached into a mount namespace of another user namespace where lock_mnt_tree() locks it. Note that unshare(CLONE_NEWNS) and clone(CLONE_NEWNS) fail with EPERM from such a mount namespace from then on. The mount can't be left out and it can't be unmounted. And refuse to move a mount of a mount namespace file beneath a locked mount in the first place. Otherwise the task ends up with a mount it can't unmount and an unshare() that fails for good. Chris also found a second mount that goes away by itself, a clone of an automounted mount that shrink_submounts() took along with its parent. Commit f78ddcc87224 ("namespace: never expire a locked mount") took care of that one. Chris's reproducer is appended. Mode nsfile reads SECRET after the unshare() on 7.3-rc7, with this patch the move_mount() fails with EINVAL and the file stays covered. nsfile-control uses an ordinary file and reads MASK both ways. // SPDX-License-Identifier: GPL-2.0 /* * Get rid of a locked cover with MOVE_MOUNT_BENEATH. * * The "admin" (root) makes a tmpfs W: * W/D file, holds SECRET, covered by a bind of a file with MASK * W/Dd/inner file, holds SECRET, Dd is covered by a bind of a directory * whose "inner" holds MASK * W/own directory of uid 1000 with the file "mine" and the * directory "minedir", whose "inner" holds MINE * W/dbg debugfs, mode 755. dbg/tracing is an automount point * The "attacker" is uid 1000. It enters a new user namespace with a new mount * namespace, so W and both covers are locked there. * * usage: prog MODE * plain put a bind of own/mine beneath the cover of D, unmount the cover * nsfile put a bind of the mount namespace file of a child beneath the * cover of D, then unshare(CLONE_NEWNS) * nsfile-control the same with a bind of own/mine * shrink put a bind of the automounted tracefs beneath the cover of Dd, * unmount the cover, put a tmpfs beneath W, call umount(W), which fails * shrink-control the same with a bind of own/minedir * The environment variable AUTOMOUNT_DIR names another automount point for "shrink". */ #define _GNU_SOURCE #include <errno.h> #include <fcntl.h> #include <grp.h> #include <sched.h> #include <signal.h> #include <stdio.h> #include <stdlib.h> #include <string.h> #include <unistd.h> ---truncated---
In the Linux kernel, the following vulnerability has been resolved: futex: Fix mm reuse handling for FUT_OFF_MMSHARED A FUT_OFF_MMSHARED futex is a shared futex that refers to an MM. It is possible for a process to wait on a shared futex with a different MM because a FUT_OFF_INODE waiter can be requeued onto a FUT_OFF_MMSHARED futex by another process. This can cause FUT_OFF_MMSHARED waiters on a freed MM to consume wakeups intended for a newly allocated MM at the same address. Fix it by keying FUT_OFF_MMSHARED using a unique 64-bit per-MM ID. Leave private futexes as before to avoid influencing the performance of the hotpath. (Multi-threaded processes typically implicitly use FUT_OFF_MMSHARED by setting clear_child_tid such that it points into anonymous memory, which causes mm_release() in a multi-threaded mm to perform FUTEX_WAKE.)
In the Linux kernel, the following vulnerability has been resolved: mshv_vtl: Check per-CPU register page before mmap Register-page setup is optional for each CPU. If allocation or registration fails, mshv_vtl_configure_reg_page() warns and leaves that CPU's reg_page NULL, but initial context setup continues successfully. Meanwhile, successful setup on another CPU sets the global mshv_has_reg_page flag. mshv_vtl_fault() checks this global flag before selecting the requested CPU's register page. With mixed setup results across online CPUs, the check passes even for a CPU with no register page, reaching get_page(NULL) when userspace faults in that mapping. Check the selected per-CPU register page before taking its reference and return VM_FAULT_SIGBUS if it is absent.
In the Linux kernel, the following vulnerability has been resolved: net/sched: fix use-after-free in __tcf_action_put() __tcf_action_put() decrements the reference count before decrementing the binding count. Another thread can free the action between these operations, causing the binding-count update to access freed memory. KASAN reports it as: BUG: KASAN: slab-use-after-free in __tcf_action_put+0x327/0x340 Write of size 4 at addr ff11000000d46420 by task tc-put-pause/64 Hold the action IDR mutex across both counter updates and IDR removal, keeping cleanup outside the lock.
In the Linux kernel, the following vulnerability has been resolved: net: rds: fix uninitialized trans dereference in CM event handler rds_rdma_cm_event_handler_cmn() assigns trans only when the RDMA device is an InfiniBand CA (RDMA_NODE_IB_CA). On any other device type, e.g. an iWARP RNIC such as siw, trans stays uninitialized, but the event switch dereferences it: unconditionally in the RDMA_CM_EVENT_CONNECT_REQUEST case via trans->cm_handle_connect(), and (with a connection context) in the ROUTE_RESOLVED and ESTABLISHED cases. An RDS listener on an iWARP device therefore crashes the kernel as soon as a connect request arrives: with CONFIG_INIT_STACK_ALL_ZERO the wild load becomes a NULL dereference at offset 0xa0 (&trans->cm_handle_connect) in the iw_cm_wq workqueue. GCC masks the bug in default builds by folding the uninitialized load into &rds_ib_transport; Clang-built kernels take the real uninitialized path and oops. The active side can land on a non-IB device too: the id that rds_ib_conn_path_connect() creates is not restricted to a node type, so rdma_resolve_addr() binds it to whichever device serves the local address, and an iWARP RNIC on the same netdev qualifies. The crash there is different: resolving a route on an iWARP id never fills in cm_id->route.path_rec, and the ROUTE_RESOLVED case writes path_rec[0].sl before it calls into the transport. The iWARP transport was dropped long ago and IB is the only transport left, so make that explicit: initialize trans to &rds_ib_transport at declaration, drop the conditional assignment, reject a connect request that arrives on a non-IB device, and drop a connection whose address resolved to one instead of resolving a route on it. The rejection is limited to RDMA_CM_EVENT_CONNECT_REQUEST on purpose: a non-zero return from the handler makes rdma_cm destroy the id the event was delivered on, which is right for the request's freshly created id but would free a connection id that RDS still owns for any other event. On the active side the id stays ic->i_cm_id and the connection's shutdown destroys it, so that case returns 0. [achender: reject only on RDMA_CM_EVENT_CONNECT_REQUEST instead of bailing out for every event on a non-IB device, so that rdma_cm does not destroy connection ids RDS still tracks; drop a connection whose address resolved to a non-IB device before a route is resolved on it; changelog adjusted]
In the Linux kernel, the following vulnerability has been resolved: sctp: revalidate output stream after association connect wait When message interleaving is enabled, the first send waits for association establishment before building its data chunks. The wait drops the socket lock, and handshake processing can reduce the output stream count to the peer-advertised inbound stream count. sctp_stream_init() then frees the extension of every removed stream. The sender resumes with the stream that it checked before the wait. If the peer removed that stream, sctp_outq_tail() later dereferences its NULL extension. Fatal-oops policies then panic the host. KASAN: null-ptr-deref in range [0x38-0x3f] RIP: sctp_outq_tail+0x49e/0xaa0 Call Trace: sctp_primitive_SEND sctp_sendmsg_to_asoc sctp_sendmsg A range check alone is insufficient. Stream reconfiguration can grow the output count again while the lock is released without recreating extensions freed by the earlier shrink. The stream can then be in range while its extension remains NULL. The send-buffer wait has the same issue. Factor the range and extension checks into a helper and repeat both after each send-path wait that drops the socket lock. Once the lock is reacquired, the validation remains stable through data creation and queueing. If validation fails after the connect wait, the auto-created association is already established. Return ESRCH so the existing caller path keeps it under state-machine ownership instead of freeing it directly, which would leave protocol, counter and socket state inconsistent.
In the Linux kernel, the following vulnerability has been resolved: spi: imx: fix slab corruption from undersized DMA bounce buffers Since commit faa8e404ad8e ("spi: imx: support dynamic burst length for ECSPI DMA mode"), the driver allocates its private DMA TX/RX buffers with kzalloc(dma_len), where dma_len is only rounded up to 4 bytes, but maps, syncs and unmaps them with DMA_CACHE_ALIGNED_LEN(dma_len), i.e. rounded up to the cache line size. As a result, the DMA API operates on memory beyond the end of the allocation. This was observed on a custom i.MX8MP platform with an mcp251xfd CAN controller under heavy RPMSG load, as a series of refcount_t warnings triggered from rpmsg_recv_done() in virtio_rpmsg_bus: refcount_t: addition on 0; use-after-free. refcount_t: underflow; use-after-free. refcount_t: saturated; leaking memory. Leading finally to an "Unable to handle kernel paging request" oops. Reproducing this problem took between 30 minutes and roughly 30 hours under the same workload. Hardware watchpoints on the refcount of a struct rpmsg_endpoint showed it was overwritten from 2 to 1 by __pi_memcpy_generic() in the irq/155-spi2.0 thread. Additionally it was found that a "normal" rpmsg_recv_done() took 11µs +/-2µs from its kref_get to kref_put. In the error case the same sequence took about 215µs +/-10µs. Based on this, an LLM was used to identify the size mismatch fixed here. Allocate the buffers with DMA_CACHE_ALIGNED_LEN(dma_len) so they cover the full mapped length, and use the same length for dma_sync_single_for_cpu() to stay consistent with map and unmap. With this patch applied, the same workload ran for more than 200 hours without the problem reproducing.
In the Linux kernel, the following vulnerability has been resolved: tracing/histograms: Reject non-stacktrace fields for synthetic stacktrace fields In check_synth_field(), when a synthetic event field is a stacktrace (field->is_stack) and the histogram field is not a "long[" stacktrace array, validation falls through to the generic size and signedness comparison. Because parse_synth_field() sets a stacktrace field's type to "__data_loc unsigned long[]", its size is sizeof(u64) and synth_field_signed() marks it as signed. Consequently, any 8-byte signed scalar histogram field passes the fallback check, and its scalar value is subsequently dereferenced as a kernel stacktrace pointer in get_field_size() and trace_stack(). Furthermore, checking strstr(hist_field->type, "long[") is insufficient because tracepoint fields defined with __bitmask() or __rel_bitmask() also have type "__data_loc unsigned long[]" or "__rel_loc unsigned long[]", whilst create_hist_field() treats them as 4-byte scalar values without HIST_FIELD_FL_STACKTRACE. Propagate HIST_FIELD_FL_STACKTRACE to variable references and field variables (whilst excluding variable aliases from per-element stacktrace capture), and reject any mismatch between HIST_FIELD_FL_STACKTRACE and field->is_stack in check_synth_field().
In the Linux kernel, the following vulnerability has been resolved: gpio: shared: fix use-after-free bug when adding shared proxies The GPIO lookup table can stay alive for longer than the kobject whose name string's address we're assigning to lookup->dev_id. Fix a potential UAF by duplicating the string.
In the Linux kernel, the following vulnerability has been resolved: i2c: viai2c-wmt: Fix clock leak in wmt_i2c_probe() In wmt_i2c_probe(), i2c->clk is acquired using of_clk_get(). If any subsequent operation fails or when the module is unloaded, the clock reference count is never decremented via clk_put(), leading to a resource leak. Switch to devm_clk_get() so that the clock is automatically managed and released.
In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Do not show buffer_meta for CPUs without a buffer The per_cpu/cpuN/buffer_meta files are created for every possible CPU, but buffer->buffers[cpu] is only allocated once that CPU comes online. Reading the file of a CPU that never came online dereferences a NULL cpu_buffer in rbm_start(). Fail the open with -ENODEV when the CPU has no buffer, as the other per CPU ring buffer interfaces do.
In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Fix the sub-buffer array base in rb_meta_subbuf_idx() On a persistent ring buffer, rb_meta_subbuf_idx() can return an index one sub-buffer too high. rb_setup_ids_meta_page() then fills subbuf_ids[] shifted by one and leaves subbuf_ids[0] NULL, which __rb_map_vma() dereferences when userspace maps trace_pipe_raw. rb_update_meta_reader() writes two such indices into meta->buffers[], which rb_cpu_meta_valid() would reject on the next boot, discarding the previous boot's trace. A CPU's sub-buffer array starts after its meta header and the nr_subbufs integers that follow, aligned up to a sub-buffer. rb_meta_subbuf_idx() inverts that calculation but skips only the integers, not the header, so its base is one sub-buffer low whenever the omitted header size crosses the alignment boundary. Invert the calculation with rb_subbufs_from_meta() rather than repeating it. rb_range_buffer() maps an index back to an address through the same helper, so the two directions can no longer disagree.
In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Fix false warning in ring_buffer_map_get_reader() The mmap reader can warn when it catches up with a writer that is still committing events. rb_get_reader_page() returns NULL in this case, but ring_buffer_map_get_reader() treats that result as an error. The initial rb_per_cpu_empty() check filters out an empty buffer, but it does not guarantee that the next reader page has committed data. Writers do not take reader_lock and can advance commit_page before publishing the committed length on the new page. rb_get_reader_page() can swap to that page, catch up with the writer and return NULL. Handle NULL through the existing no-data exit without warning. Remove the caller's reader_page == commit_page check as well, since the reader-page helper already handles that case. The existing metadata update and return path remain in place.
In the Linux kernel, the following vulnerability has been resolved: scsi: bsg: Pass reply_len to bsg_setup_queue() to fit UFS ARPMB replies bsg-lib allocates a 96-byte (SCSI_SENSE_BUFFERSIZE) reply buffer per job, but struct ufs_rpmb_reply is 104 bytes: a 40-byte struct ufs_bsg_reply followed by a 64-byte EHS. When an Advanced RPMB command returns an EHS, ufshcd_advanced_rpmb_req_handler() copies it right after the 40-byte header and writes 8 bytes past the end of the buffer. Let each BSG transport pass its reply buffer size to bsg_setup_queue() and have ufs_bsg request sizeof(struct ufs_rpmb_reply), so the full reply reaches user space. Other transports keep SCSI_SENSE_BUFFERSIZE.
In the Linux kernel, the following vulnerability has been resolved: scsi: st: Fix use-after-free race between st_remove() and st_open() st_remove() drops the probe reference on the scsi_tape with kref_put() and only afterwards removes its index from st_index_idr. If that was the last reference, scsi_tape_release() frees the structure while it is still published in the idr. scsi_tape_get(), called from st_open(), looks up the tape in st_index_idr and takes a reference under st_ref_mutex and st_index_lock. remove_cdevs() does not wait for opens that are already past chrdev_open(), so an open that is blocked on st_ref_mutex while st_remove() holds it can take the mutex as soon as st_remove() drops it, find the freed tpnt in the idr and call kref_get() on it: BUG: KASAN: slab-use-after-free in st_open Write of size 4 ... st_open (drivers/scsi/st.c:254 drivers/scsi/st.c:1291) chrdev_open ... Freed by task ...: kfree st_remove (drivers/scsi/st.c:4512) Remove the index from the idr before dropping the reference, all under st_ref_mutex. A concurrent scsi_tape_get() now either runs first and holds a valid reference that keeps the tape alive, or runs afterwards and finds nothing, so st_open() fails with -ENXIO. This restores the ordering st_remove() had before the conversion to st_index_idr, where the tape was unpublished from scsi_tapes[] before the final kref_put().
In the Linux kernel, the following vulnerability has been resolved: scsi: xen/scsifront: Check for a NULL shadow entry on a backend response scsifront_do_response() validates the rqid in a backend response against VSCSIIF_MAX_REQS before using it to index info->shadow[], but then dereferences the entry to test ->inflight without checking that the slot is populated. Shadow slots are NULL before a command is submitted (the host private area is zeroed at allocation) and are reset to NULL in _scsifront_put_rqid() once a request completes, so an in-range rqid that does not correspond to an outstanding request makes the frontend dereference a NULL pointer. A malicious or buggy backend can thus crash the guest by returning a response whose rqid is in range but not in flight -- for example a spurious response before any command has been issued, or a duplicate of one already completed. The ring has only VSCSIIF_MAX_REQS (16) slots, so before the first command every in-range rqid selects a NULL slot. Reject a response whose shadow slot is not populated.
In the Linux kernel, the following vulnerability has been resolved: scsi: libiscsi: Reject a negative task index from parse_pdu_itt A transport that implements parse_pdu_itt hands libiscsi an index taken from the PDU, and both lookups bound it from above only: if (i >= session->cmds_max) i and cmds_max are both int, so a negative index passes and session->cmds[i] is read from before the array. be2iscsi produces one. beiscsi_parse_pdu() assigns the raw tag, *index = (int)itt; and beiscsi_complete_pdu() forwards an unsolicited NOP-In from the hardware async ring without replacing its ITT, so the value is the target's. It also reports the session's own age rather than the one in the tag, which leaves the age comparison in iscsi_verify_itt() with nothing to reject. Bound the index from below in both lookups.
In the Linux kernel, the following vulnerability has been resolved: scsi: libiscsi: Validate the ITT reflected in a Reject PDU A Reject PDU carries a copy of the header it rejects, and iscsi_handle_reject() takes the ITT out of that copy to find the task to clean up: memcpy(&rejected_pdu, data, sizeof(struct iscsi_hdr)); ... task = iscsi_itt_to_task(conn, rejected_pdu.itt); That value is whatever the target put there. iscsi_itt_to_task() bounds the index against cmds_max and checks nothing else, so any task in the pool can be named, and iscsi_nop_out_rsp() then completes it. An index that has never been used gives a NULL task->conn: the pool is zeroed at session setup and conn is assigned only when a task is allocated. If the task was used and returned, iscsi_complete_task() hits its WARN_ON_ONCE(task->state == ISCSI_TASK_FREE) and the refcount underflows. An in-flight SCSI command is completed as successful - a 1 MiB read returned 1048576 with none of its buffer written and no warning. Validate the reflected ITT the way iscsi_itt_to_ctask() validates a command ITT, and require the task to be in flight and not a SCSI command. [ 6.248477] Oops: general protection fault, probably for non-canonical address 0xdffffc000000000c: 0000 [#1] SMP KASAN NOPTI [ 6.249357] KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067] [ 6.249951] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 7.2.0-rc5-ISCSI1-gf5098b6bae76 #1 PREEMPT(lazy) [ 6.250718] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 6.251616] RIP: 0010:iscsi_nop_out_rsp.constprop.0+0x46/0x160 [ 6.252043] Code: c1 ea 03 48 83 ec 08 80 3c 02 00 0f 85 f5 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 58 48 8d 7d 60 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 c0 00 00 00 48 8b 45 60 48 39 c3 74 50 48 b8 00 [ 6.252813] RSP: 0018:ffff88806c907b80 EFLAGS: 00010206 [ 6.253042] RAX: dffffc0000000000 RBX: ffff88800607e000 RCX: ffffffff8d571a25 [ 6.253345] RDX: 000000000000000c RSI: ffff88806c907c38 RDI: 0000000000000060 [ 6.253642] RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff235a504 [ 6.253947] R10: 0000000000000003 R11: 7463656e6e6f6320 R12: 0000000000000000 [ 6.254251] R13: 0000000000000000 R14: ffff88806c907c38 R15: 0000000000000000 [ 6.254549] FS: 0000000000000000(0000) GS:ffff8880d95bc000(0000) knlGS:0000000000000000 [ 6.254887] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6.255140] CR2: 00007fc393e8ffc0 CR3: 0000000005252006 CR4: 0000000000770ef0 [ 6.255439] PKRU: 55555554 [ 6.255564] Call Trace: [ 6.255674] <IRQ> [ 6.255768] __iscsi_complete_pdu+0x18bf/0x22a0 [ 6.256733] iscsi_complete_pdu+0x54/0xa0 [ 6.256905] iscsi_tcp_data_recv_done+0xf4/0x250 [ 6.257103] iscsi_tcp_recv_skb+0x31e/0xec0 [ 6.257680] iscsi_sw_tcp_recv+0x12f/0x390 [ 6.258061] __tcp_read_sock+0x1ab/0x810 [ 6.258853] iscsi_sw_tcp_data_ready+0x18b/0x510 [ 6.259808] tcp_data_queue+0x1f13/0x4cd0 [ 6.260567] tcp_rcv_established+0x8a5/0x3a00 [ 6.261931] tcp_v4_do_rcv+0x449/0x960 [ 6.262269] tcp_v4_rcv+0x2245/0x3bc0
In the Linux kernel, the following vulnerability has been resolved: scsi: libiscsi: Validate the task named by a management response __iscsi_complete_pdu() fetches the task for five response types from one place and checks only that the index resolved: case ISCSI_OP_LOGOUT_RSP: case ISCSI_OP_LOGIN_RSP: case ISCSI_OP_TEXT_RSP: case ISCSI_OP_SCSI_TMFUNC_RSP: case ISCSI_OP_NOOP_IN: task = iscsi_itt_to_task(conn, hdr->itt); if (!task) return ISCSI_ERR_BAD_ITT; iscsi_itt_to_task() bounds the index against cmds_max and looks at nothing else, so a target can name any slot in the pool, including one that has never been used. task->conn is then NULL, and both iscsi_nop_out_rsp() and iscsi_complete_task() dereference it. One unsolicited NOP-In is enough; a Text Response carrying the same ITT crashes in iscsi_complete_task() instead. Require the task to be in flight and not a SCSI command, the way iscsi_itt_to_ctask() does for the command opcodes. [ 6.298634] Oops: general protection fault, probably for non-canonical address 0xdffffc000000000c: 0000 [#1] SMP KASAN NOPTI [ 6.298642] KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067] [ 6.298652] CPU: 1 UID: 0 PID: 111 Comm: iscsistart Not tainted 7.2.0-rc5-ISCSI1-gf5098b6bae76 #1 PREEMPT(lazy) [ 6.298654] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 6.298656] RIP: 0010:iscsi_nop_out_rsp.constprop.0+0x46/0x160 [ 6.298691] Code: c1 ea 03 48 83 ec 08 80 3c 02 00 0f 85 f5 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 58 48 8d 7d 60 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 c0 00 00 00 48 8b 45 60 48 39 c3 74 50 48 b8 00 [ 6.298698] RSP: 0018:ffff88806c907be8 EFLAGS: 00010206 [ 6.298701] RAX: dffffc0000000000 RBX: ffff888006116800 RCX: 0000000000000020 [ 6.298702] RDX: 000000000000000c RSI: ffff88800525d578 RDI: 0000000000000060 [ 6.298703] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 6.298706] R10: 0000000000000020 R11: 0000000000000000 R12: 0000000000000000 [ 6.298706] R13: 000000000000002e R14: ffff8880056eb440 R15: ffff888006116800 [ 6.298707] FS: 00007fc02d1c2740(0000) GS:ffff8880b29bc000(0000) knlGS:0000000000000000 [ 6.298710] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6.298711] CR2: 000055fe3b56ddf8 CR3: 00000000053b9004 CR4: 0000000000770ef0 [ 6.298712] PKRU: 55555554 [ 6.298713] Call Trace: [ 6.298714] <IRQ> [ 6.298714] __iscsi_complete_pdu+0x13a8/0x22a0 [ 6.298758] iscsi_complete_pdu+0x54/0xa0 [ 6.298759] iscsi_tcp_hdr_recv_done+0x870/0x2c80 [ 6.298778] iscsi_tcp_recv_skb+0x31e/0xec0 [ 6.298800] iscsi_sw_tcp_recv+0x12f/0x390 [ 6.298804] __tcp_read_sock+0x1ab/0x810 [ 6.298812] iscsi_sw_tcp_data_ready+0x18b/0x510 [ 6.298814] tcp_rcv_established+0x1f56/0x3a00 [ 6.298842] tcp_v4_do_rcv+0x449/0x960 [ 6.298847] tcp_v4_rcv+0x2245/0x3bc0
In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix NULL sink dereference in USB4 bandwidth functions allocate_usb4_bandwidth_for_stream() and allocate_usb4_bandwidth() both use ASSERT(stream->sink) before dereferencing stream->sink->link. ASSERT is compiled out in production builds, so a NULL stream->sink causes a NULL pointer dereference. link_set_dpms_off() already guards two earlier accesses to stream->sink with explicit NULL checks, confirming that stream->sink can legitimately be NULL. The subsequent call to deallocate_usb4_bandwidth() had no equivalent guard. Replace the ASSERT() calls with proper NULL checks that return false early, and add a matching stream->sink guard at the call site in link_set_dpms_off() consistent with the surrounding pattern. v2: Keep the existing ASSERT() calls for diagnostics (to report unexpected NULL sink), and add explicit NULL checks that return false before dereferencing stream->sink. Also add a matching stream->sink guard at the deallocation call site in link_set_dpms_off(). (Alex) (cherry picked from commit 98029a0ce61feb52c563f65349dd9b25f672e355)
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: don't drop the runtime PM reference twice in amdgpu_gpr amdgpu_debugfs_gpr_read() drops its runtime PM reference right after reading the wave registers. When copying them to userspace fails, it jumps to the err label, which drops the reference a second time. A read into a bad buffer on Navi31 either steals a reference somebody else holds (power/runtime_usage goes from 1 to 0) or underflows the count: amdgpu 0000:03:00.0: Runtime PM usage count underflow! The registers are already in the kernel buffer at that point, so finish the hardware access first and copy the buffer with a single copy_to_user() instead of the put_user() loop with its own error path. (cherry picked from commit 31035bbd74f7c3e10c163db875b8e67f8b50ee6a)
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix GEM object leak on ENOMEM in userptr ioctl When amdgpu_hmm_range_alloc() fails amdgpu_gem_userptr_ioctl() returns -ENOMEM right away and skips the cleanup every other error path goes through. The GEM object, the bo->parent reference on the VM root and the MMU notifier registration are all left behind. Use release_object here, not user_pages_done, range is still NULL at this point. (cherry picked from commit bbe739e407a542073ec1a7872b14843566b4919e)
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: keep the eviction fence until the last handle is closed amdgpu_gem_object_close() detaches the user queue eviction fence from the BO before it checks bo_va->ref_count, so closing any handle of a BO removes the fence, even when the file still has another handle to the BO and the bo_va with its GPU mappings stays. The BO can then be evicted without suspending the user queues of the file, which keep accessing it through mappings that are only marked for update. Seen on navi31 with a SDMA user queue: a BO opened twice in the same file (GEM_FLINK + GEM_OPEN) loses its eviction fence when the second handle is closed (traced attach/detach of the fence): attach bo=ffff8c78a6c84c00 GEM_CLOSE handle=7 detach bo=ffff8c78a6c84c00 while handle 6 and the mapping are still in use. Only detach the fence when the last reference to the bo_va goes away, matching amdgpu_gem_object_open(), which attaches it only when the bo_va is created. With this the fence stays until the file is closed. (cherry picked from commit 8387982f03d4026b7dc11b0b5e3118298eee4d6a)
In the Linux kernel, the following vulnerability has been resolved: drm/exec: don't immediately add prelocked obj to array of locked objs When a contention is detected the drm_exec object grabs a reference to the contended object, unlocks all other objects and pre-locks the contended one before anything else. The problem is that it is possible that this pre-locked object was about to be destroyed and drm_exec is now holding the last reference to it. So we never actually see this pre-locked object again to be explicitly locked and so also never reserve a slot for a dma_fence object on it. Should the driver now use drm_exec_for_each_locked_object() to add a new fence to all locked objects we eventually see a warning or even a BUG_ON() to prevent random memory corruption. Fix this by keeping the prelocked object out of the array of locked objs until it was explicitly mentioned by the driver again. If the prelocked object is never mentioned again by the driver just unlock and drop the reference at the end of the locking loop.
In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Add sanity check for DMC load address For DMC firmware header version 3, the firmware load address is stored in dmc_info->start_mmioaddr and later used by dmc_load_program(). Unlike the MMIO address table, the firmware load address is not validated. Add a sanity check to ensure it is within the valid range. BSpec: 69671, 68378 (cherry picked from commit 5e47ee5c76ca9becde8df4ad5202845b7ffcbc4c)
In the Linux kernel, the following vulnerability has been resolved: drm/xe: Don't transfer shrinker pages for pinned bos on purgeable state change Pinned bos have their pages removed from the shrinker's shrinkable / purgeable counts on pin, and added back on unpin according to the bo's purgeable state at that time. However, xe_bo_set_purgeable_shrinker() unconditionally transfers pages between the shrinkable and purgeable counts. If the purgeable state of a pinned bo changes, for example by userspace madvising DONTNEED on a VMA of a bo that is also pinned as a scanout buffer, this underflows one count and, after unpin, leaves the other one permanently inflated. Only update the purgeable flag for pinned bos, and leave the page accounting to unpin. (cherry picked from commit afe6bc012034123fd838328668e609bf57e46bd3)
In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix use-after-free of a destroyed user DSQ by a deferred reenqueue A deferred reenqueue can read a freed user DSQ. The request stays on its CPU's deferred list until run_deferred() takes it, and the RCU callback that frees the DSQ assumes that the grace period has flushed it, so exit_dsq() checks the per-CPU node without the deferred list lock. A grace period waits for readers in flight, not for a pending run_deferred(). A run_deferred() which starts after the grace period began can detach the request right before the callback looks and then read the freed DSQ's id. Cancel the pending requests before the grace period instead. The irq work that frees the DSQ unlinks every CPU's request under the per-CPU deferred list lock, and schedule_dsq_reenq() ignores a new request under the same lock once the id is invalid. Only a run_deferred() that started before the grace period can hold a request, and it runs with IRQs disabled, so the grace period waits for it and nothing touches the DSQ after the callback.
In the Linux kernel, the following vulnerability has been resolved: tracing: Keep the predicate limit separate from program capacity predicate_parse() adds two to nr_preds to reserve the terminal TRUE and FALSE entries. It also uses that increased value as the limit for parsed predicates. If the initial count is smaller than the number actually parsed, the program can fill the allocation and subsequent accesses can go past its end. Keep nr_preds as the predicate limit and use a separate value for the allocation size. This leaves space for both terminal entries and a zeroed entry when parsing stops at the limit.
In the Linux kernel, the following vulnerability has been resolved: tracing: Check operator stack capacity before pushing predicate_parse() uses the first operator stack entry before processing any opening parentheses. A push then increments top before writing. The existing check still permits that write when top already points to the last allocated entry, which can access beyond the operator stack. Reject the push when top reaches the last allocated entry.
In the Linux kernel, the following vulnerability has been resolved: tracing: Fix crash in print_graph_function_event() tracing_set_tracer() assigns the flags of the newly selected tracer with: tr->current_trace_flags = t->flags ? : t->tracer->flags; If the new tracer defines neither static flags nor default flags, like hwlat, irqsoff or wakeup, add_tracer() has no per instance flags copy for it, and both operands are NULL, so tr->current_trace_flags ends up being NULL as well. The ring buffer is not cleared when switching tracers: it is reset inside tracer_init(), after current_trace_flags was already assigned. If the buffer still holds function_graph entries of the previous tracer, printing one of them dereferences the NULL pointer. This was hit by cat trace during an ftrace stress test: BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode RIP: 0010:print_graph_function_event+0xe/0x20 Call Trace: s_show+0x4d/0x110 seq_read_iter+0x2d4/0x490 seq_read+0x130/0x170 vfs_read+0xb5/0x370 ksys_read+0x6d/0xe0 do_syscall_64+0xbc/0x450 The snapshot buffer is not reset at all, so this can be reproduced without a race: echo function_graph > /sys/kernel/tracing/current_tracer echo 1 > /sys/kernel/tracing/snapshot echo hwlat > /sys/kernel/tracing/current_tracer cat /sys/kernel/tracing/snapshot Rather than teaching every user of tr->current_trace_flags about this corner case, make sure it is never NULL: when the newly selected tracer has no flags at all, tracing_set_tracer() falls back to a static empty no_tracer_flags. run_tracer_selftest() can hit the same case, so the same fallback is added there too. The existing users already handle opts == NULL, so these tracers keep behaving as before.
In the Linux kernel, the following vulnerability has been resolved: tracing: Fix hist trigger timestamps for buffered events Syzkaller triggered a WARN_ON_ONCE(!nest) warning: WARNING: kernel/trace/ring_buffer.c:821 at ring_buffer_event_time_stamp Call trace: ring_buffer_event_time_stamp hist_field_timestamp hist_fn_call event_hist_trigger event_triggers_call __event_trigger_test_discard trace_event_buffer_commit do_trace_event_raw_event_sched_switch trace_event_raw_event_sched_switch The warning is probabilistically reproducible and is related to syzkaller executing the following commands: echo 'prev_pid == 999999' > events/sched/sched_switch/filter echo 'hist:keys=common_timestamp' > events/sched/sched_switch/trigger The specific triggering process is as follows: CPU 0 CPU 1 (context switching) (echo 'hist:keys=common_timestamp' > \ events/sched/sched_switch/trigger) do_trace_event_raw_event_##call trace_event_buffer_lock_reserve if (!tr->no_filter_buffering_ref && trace_file->flags & EVENT_FILE_FL_FILTERED) return entry; // return directly event_hist_trigger_parse hist_register_trigger tracing_set_filter_buffering(file->tr, true); tr->no_filter_buffering_ref++; __trace_buffer_lock_reserve rb_start_commit local_inc(&cpu_buffer->committing); // skipped and not executed trace_event_buffer_commit __event_trigger_test_discard event_triggers_call event_hist_trigger hist_fn_call hist_field_timestamp ring_buffer_event_time_stamp nest = local_read(&cpu_buffer->committing); WARN_ON_ONCE(!nest) // trigger warning The root cause is that when an event file has a filter attached and the hist trigger has not yet been attached, trace_event_buffer_lock_reserve() writes the event into the per-CPU trace_buffered_event temp buffer instead of reserving it in the ring buffer, so cpu_buffer->committing is not incremented. When the event is later processed at commit time by a hist trigger, hist_field_timestamp() -> ring_buffer_event_time_stamp() sees a zero committing count, triggering WARN_ON_ONCE(!nest). tracing_event_time_stamp() was added by commit d8279bfc5e959 ("tracing: Add tracing_event_time_stamp() API") for exactly this case: if the event is the per-CPU trace_buffered_event, it returns the current ring buffer timestamp. But it never gained a caller. Use it in hist_field_timestamp(), so that a hist trigger that races onto a buffered event records the current time, which is only marginally later than when the event was recorded, instead of warning and recording a bogus timestamp.