In the Linux kernel, the following vulnerability has been resolved: net/rds: use wq_has_sleeper() in release_in_xmit() release_in_xmit() clears RDS_IN_XMIT with clear_bit_unlock() and then checks waitqueue_active() to decide whether anyone needs waking. clear_bit_unlock() is only a release operation: it orders the critical section before the bit clear, but does not order the subsequent plain load of the wait queue head after it. The waiter side does the mirror image - it adds itself to the wait queue and then tests the bit. That is the classic store-buffering pattern: the releasing CPU can read the wait queue as empty while the waiting CPU still reads the bit as set, so the sleeper is never woken. The waiters are rds_conn_shutdown() and rds_tcp_reset_callbacks(), both in uninterruptible wait_event() with no timeout. A lost wake-up strands the shutdown worker on its single-threaded workqueue until some other sender releases the bit again - and on a connection that is being torn down precisely because it failed, there may never be another sender. The barrier used to be there: release_in_xmit() did clear_bit() followed by smp_mb__after_atomic() until commit 1422f28826d2 ("rds: introduce acquire/release ordering in acquire/release_in_xmit()") folded both into clear_bit_unlock(), which strengthened the lock hand-off but silently dropped the full barrier the wake-up check depends on. The refill counterpart, release_refill() in net/rds/ib_recv.c, still carries its smp_mb__after_atomic() for exactly this reason. Use wq_has_sleeper(), which is waitqueue_active() preceded by the required full barrier.
In the Linux kernel, the following vulnerability has been resolved: net/rds: clear cp_flags bits individually in rds_conn_path_reset() rds_conn_path_reset() wipes the whole flag word with a plain cp->cp_flags = 0 store. Every other accessor of that word uses atomic bitops, and some of them can run concurrently with the reset: RDS_LL_SEND_FULL is set from rds_send_xmit() and cleared from the transport completion paths, neither of which holds anything that excludes the shutdown worker. A plain store racing an atomic read-modify-write on the same word is a data race, and whichever side loses has its update silently discarded. Clear the two bits the reset is actually responsible for instead. RDS_IN_XMIT and RDS_RECV_REFILL need no store at all here: they belong to the caller, rds_conn_shutdown(), which waits for both to be clear before calling the transport shutdown and this reset. This also gives every bit in cp_flags a single well-defined writer discipline, which the following patches rely on when they turn RDS_IN_XMIT and RDS_RECV_REFILL into bit locks held across the teardown: a blanket store mid-teardown would destroy lock ownership that an atomic clear preserves. Oracle UEK carries the same conversion ("net/rds: Preserve essential connection state flags"), motivated by its asynchronous shutdown state machine, whose progress and destroy flags must survive the reset. UEK's variant also clears RDS_IN_XMIT and RDS_RECV_REFILL because there the reset runs as the final step of a teardown that owns both bits, making those clears its unlock. Upstream that release belongs in rds_conn_shutdown(): once a later patch in this series turns the two bits into locks held across the teardown, ending ownership needs release semantics and a wake-up that a plain clear inside the reset would not provide. Based on Oracle UEK commit "net/rds: Preserve essential connection state flags" by Gerd Rausch.
In the Linux kernel, the following vulnerability has been resolved: net/rds: don't let rds_conn_shutdown() consume a concurrent drop rds_conn_shutdown() finishes by moving the path from RDS_CONN_DISCONNECTING to RDS_CONN_DOWN, and also accepts RDS_CONN_ERROR as the starting state of that final transition, so that a FIN processed in softirq context during the teardown does not derail the shutdown into a noisy error path. But consuming that RDS_CONN_ERROR also consumes the shutdown pass that came with it: rds_conn_path_drop() sets RDS_CONN_ERROR and then queues cp_down_w, and a pass that starts on a path already in RDS_CONN_DOWN is a no-op. For the FIN case that is harmless - the socket the FIN arrived on is the very socket the teardown just released. It is not harmless for a dropper that attached something to the path first. rds_tcp_accept_one() is such a dropper. Its path claim in rds_tcp_accept_one_path() transitions RDS_CONN_DOWN -> RDS_CONN_CONNECTING, and a concurrent drop - a FIN on a previous socket in softirq context, an administrative reset - can put the path into RDS_CONN_ERROR between that claim and the state check that follows, which accepts RDS_CONN_ERROR. The accept then installs the freshly accepted socket with rds_tcp_set_callbacks() while the queued teardown - which sampled tc->t_sock before this socket existed - is still running. rds_connect_path_complete() fails its transition to RDS_CONN_UP and drops the path again, queueing the pass that should reap the socket it just installed. If the in-flight shutdown's final transition consumes that drop's RDS_CONN_ERROR, the queued pass finds the path in RDS_CONN_DOWN and does nothing. The installed socket is never torn down: it sits established with its callbacks armed and its rds_tcp_connection on rds_tcp_tc_list, the peer sees a connection that nothing ever reads, and the path is wedged in RDS_CONN_DOWN until some later event drops it again. Reproduced with widened race windows as an ever-growing receive queue on a socket owned by a path stuck in RDS_CONN_DOWN, with the peer's send path wedged behind it. Make the final transition only DISCONNECTING -> DOWN. If it fails because the path is in RDS_CONN_ERROR, a drop raced the teardown: cancel the reconnect timer and clear RDS_RECONNECT_PENDING - the one piece of the skipped tail that must not be left behind - and return, letting the pass the drop queued finish the job: it tears down whatever attached to the path in the meantime, completes the transition to RDS_CONN_DOWN, and re-arms the reconnect from its own tail. The timer quiesce in that branch matters because the racing drop does not always queue that pass: rds_conn_path_drop() returns without queueing when a destroy is pending - exactly the situation during a netns teardown or module unload, when a FIN on the dying socket is processed while rds_conn_path_destroy() flushes cp_down_w. If the flushed pass is the one that takes this return, no later pass exists, and rds_conn_path_destroy() would find cp_conn_w still armed (WARN_ON) and then free a path whose reconnect timer can still fire. With the cancel in the branch, every exit of a shutdown pass leaves the timer quiesced no matter which pass completes the transition. The FIN case keeps making progress, one pass later and still without noisy logging. Any other state keeps today's rds_conn_path_error() handling; no current cp_state writer can leave a DISCONNECTING path in anything but RDS_CONN_ERROR (every other writer is a cmpxchg from a non-DISCONNECTING state), so that branch is defensive. On kernels without the preceding patches the same hazard exists with the sample-based quiesce; the fix applies there equally.
In the Linux kernel, the following vulnerability has been resolved: ALSA: caiaq: Fix potential double-free at error path The fix for caiaq driver's resource management to handle the errors tries to release the resources in a common destructor call, but as a sashiko review for another patch suggested, some of the audio resources such as URBs have been already freed, and this may lead to a double-free. For addressing the double-free, call the common destructor function from each place, and assure that the resource pointers get cleared.
In the Linux kernel, the following vulnerability has been resolved: bpf: Fix NULL-ptr-deref when showing a void BTF type btf_modifier_show() resolves the modifier and then calls btf_type_ops(t)->show() unconditionally. For the void type (type_id 0, BTF_KIND_UNKN) kind_ops[] has no entry, so ->show is NULL. A "const void" (a modifier resolving to void) cannot be a map key or value - map_check_btf() rejects it because void has no size - so the map dump path does not reach it. But bpf_snprintf_btf() takes a type_id straight from the BPF program, and passing such a "const void" from the vmlinux BTF NULL-derefs: KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] RIP: 0010:btf_modifier_show (kernel/bpf/btf.c:2914) Call Trace: <TASK> btf_type_show (kernel/bpf/btf.c:8251) btf_type_snprintf_show (kernel/bpf/btf.c:8321) bpf_snprintf_btf (kernel/trace/bpf_trace.c:1047) bpf_prog_test_run_raw_tp (net/bpf/test_run.c:829) __sys_bpf (kernel/bpf/syscall.c:4804) do_syscall_64 (arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) </TASK> Fall back to btf_df_show() when the resolved type has no show op; it emits the "<unsupported kind:N>" placeholder already used for kinds like FWD and FUNC. bpf_snprintf_btf() then returns the length as usual.
In the Linux kernel, the following vulnerability has been resolved: bpf: Fix NULL-ptr-deref in btf_var_show() btf_var_show() calls btf_type_id_resolve() unconditionally, which dereferences btf->resolved_ids. That is NULL for a base BTF - e.g. the vmlinux BTF that bpf_snprintf_btf() renders against - since base BTF is not resolved during parsing. btf_modifier_show() guards this with 'if (btf->resolved_ids)', but btf_var_show() does not. A BPF program that passes the type_id of a BTF_KIND_VAR from the vmlinux BTF to bpf_snprintf_btf() thus NULL-derefs: KASAN: probably user-memory-access in range [0x46638-0x4663f] RIP: 0010:btf_var_show (kernel/bpf/btf.c:2929) Call Trace: <TASK> btf_type_show (kernel/bpf/btf.c:8259) btf_type_snprintf_show (kernel/bpf/btf.c:8329) bpf_snprintf_btf (kernel/trace/bpf_trace.c:1047) bpf_prog_test_run_raw_tp (net/bpf/test_run.c:829) __sys_bpf (kernel/bpf/syscall.c:4804) do_syscall_64 (arch/x86/entry/syscall_64.c:84) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) </TASK> Resolve the var's type directly with btf_type_skip_modifiers() when resolved_ids is NULL, mirroring btf_modifier_show().
In the Linux kernel, the following vulnerability has been resolved: bpf: Mark sched_process_wait argument as nullable do_wait() passes wo->wo_pid to the sched_process_wait tracepoint. kernel_wait4() leaves wo_pid NULL for wait4(-1), and kernel_waitid_prepare() does likewise for waitid(P_ALL). btf_ctx_access() currently types argument 0 as PTR_TO_BTF_ID | PTR_TRUSTED. Without PTR_MAYBE_NULL, the verifier accepts an unchecked dereference. Trusted pointer loads have no fault protection, so a wait for any child can then cause a NULL pointer dereference in JITed BPF code. Add sched_process_wait to raw_tp_null_args[] with argument 0 marked nullable. The verifier rejects an unchecked dereference while preserving access after the program checks the pointer for NULL.
In the Linux kernel, the following vulnerability has been resolved: bpf: Mark bpf_btf_find_by_name_kind() as sleepable When bpf_btf_find_by_name_kind() finds a type in module BTF, it returns a new BTF object fd through __btf_new_fd(). This reaches anon_inode_getfd(), which can sleep while allocating or expanding the current task fd table. The helper prototype does not set might_sleep, so the verifier allows the helper in non-sleepable contexts such as BPF timer callbacks. The fd allocation can then sleep in softirq context and install the fd into the interrupted task. Mark the helper as sleepable. This preserves calls from the main body of a sleepable syscall program while rejecting calls from its non-sleepable regions.
In the Linux kernel, the following vulnerability has been resolved: bpf: Mark faultable stack helpers as sleepable The faultable variants of bpf_get_stack() and bpf_get_task_stack() pass may_fault=true into the common stack collection code. Resolving user-space build IDs may then call build_id_parse_file() and block on filesystem reads. Neither helper prototype sets might_sleep. Since prototype selection uses the sleepability of the whole program, the verifier can still allow these helpers from a non-sleepable region within that program, such as an explicit RCU or preemption-disabled region. The task-stack helper can also be called from a non-sleepable timer callback of a sleepable program. Mark both faultable prototypes as sleepable. The existing helper context check then rejects these calls while continuing to allow them in genuinely sleepable contexts.
In the Linux kernel, the following vulnerability has been resolved: bpf: Require MEM_PERCPU for percpu kptr stores map_kptr_match_type() treats perm_flags as the set of register type flags that a kptr field permits. Adding MEM_PERCPU to that set for BPF_KPTR_PERCPU does not require the source register to carry it, however. The subset test consequently accepts both a plain bpf_obj_new() allocation and a referenced kernel pointer into a __percpu_kptr map field. Loads from the field are always marked MEM_PERCPU. Consumers then treat the stored value as the cookie returned by bpf_percpu_obj_new(): per-CPU pointer helpers relocate it, and map teardown selects the per-CPU free path. A plain allocation can therefore provide an arbitrary kernel read/write, while a kernel pointer can be relocated into an invalid address or sent through a missing destructor. Require the source MEM_PERCPU flag to match the destination field kind. This preserves valid bpf_percpu_obj_new() stores and rejects both the program-BTF and kernel-BTF variants.
In the Linux kernel, the following vulnerability has been resolved: bpf: Reject untrusted allocated-object pointers When the final RCU read-side critical section ends, a local kptr is demoted to PTR_UNTRUSTED but retains MEM_ALLOC. The pointer may be NULL or may refer to an object whose lifetime is no longer protected. type_is_ptr_alloc_obj() nevertheless recognizes any PTR_TO_BTF_ID with MEM_ALLOC as a live allocated object. In particular, a refcount-only local kptr never carries NON_OWN_REF, so it still passes the bpf_refcount_acquire() argument check after RCU protection ends. The kfunc can then dereference NULL or stale memory. Make type_is_ptr_alloc_obj() reject PTR_UNTRUSTED pointers. Since type_is_non_owning_ref() is based on the same predicate, graph kfunc arguments obey the same live-object requirement. Fault-protected reads of the demoted pointer remain valid: writes are already rejected, and read fixups use bpf_may_fault_on_deref() rather than this predicate. [ kkd: Rewrote commit log ]
In the Linux kernel, the following vulnerability has been resolved: nexthop: Initialize extack in remove_nh_grp_entry() remove_nh_grp_entry() prints the extack message when a listener fails to replace the reduced nexthop group. However, extack is not initialized and listeners are not required to set a message when returning an error. Neither netdevsim nor mlxsw do so when an allocation fails, resulting in the dereference of an uninitialized stack pointer. Fix by zero-initializing extack, as was done in commit 6347c5314cee ("nexthop: initialize extack in nh_res_bucket_migrate()").
In the Linux kernel, the following vulnerability has been resolved: eth: nfp: drop the replaced rule from the list when reprogramming fails nfp_net_fs_add() replaces an existing rule by deleting it from the hardware, decrementing nn->fs.count and programming the new one. If nfp_net_fs_add_hw() fails the old entry stays on nn->fs.list - only the success path reaches list_replace() - so the list is one longer than nn->fs.count, and it advertises a rule whose hardware entry has already been torn down. nn->fs.count is what ETHTOOL_GRXCLSRLCNT reports, so userspace then sizes its buffer one entry short of what the GRXCLSRLALL walk wants to write. That used to overwrite one u32 past the allocation; since the walk is bounded it is a permanent -EMSGSIZE instead, as nothing ever resyncs the counter.
In the Linux kernel, the following vulnerability has been resolved: net: bridge: mcast: properly convert mglist to rcu Sashiko reported a bug [1] that br_multicast_del_port_group unlists the port group not using proper rcu helper that preserves the next pointer and after that immediately frees the port group without waiting for rcu grace period. The only rcu walker of mglist is br_multicast_list_adjacent() and it turns out that function has always been buggy because mglist was never properly converted to RCU. Fix it by converting it to rcu and moving its initialization after eth_addr's. Initializing p->next can use RCU_INIT_POINTER because we have a barrier from the hlist_add_head_rcu call later, besides we're initializing an unpublished structure anyway. [1] https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20260826014200.362304-1-littleddfu%40gmail.com
In the Linux kernel, the following vulnerability has been resolved: s390/ism: folio_put() after error dmb->cpu_addr was allocated via folio_alloc(). Use folio_put() instead of kfree() in the error exit of ism_alloc_dmb() to avoid slab allocator corruption. While at it, reset dmb->cpu_addr after folio_put to avoid unintentional UAF by future callers.
In the Linux kernel, the following vulnerability has been resolved: net: cap tx_queue_len at S16_MAX to prevent oversized ring allocations Several subsystems allocate ring buffers sized by dev->tx_queue_len with no upper bound. An unprivileged user (via unshare -Urn) can set a huge tx_queue_len and exhaust global memory with ring allocations: - pfifo_fast: pfifo_fast_init() and pfifo_fast_change_tx_queue_len() allocate 3 skb_array rings of tx_queue_len entries each. - tun: tun_queue_resize() and the queue-attach path resize ptr_rings to tx_queue_len on the NETDEV_CHANGE_TX_QUEUE_LEN notifier. - tap (macvtap/ipvtap): tap_queue_resize() and tap_init() resize/init ptr_rings to tx_queue_len on the same notifier. netif_change_tx_queue_len() is the single entry point for IFLA_TXQLEN, sysfs, and the SIOCSIFTXQLEN ioctl. Cap new_len at S16_MAX (32767) there so the oversized value is rejected at set time. This takes effect whether the device is up or down, before dev->tx_queue_len is written, before any notifier fires, and before any ring is allocated. The "> S16_MAX" check also subsumes the previous unsigned-long truncation test, and a negative ifr_qlen from the ioctl lands far above the cap after conversion, so both old failure modes are covered by the one comparison. tx_queue_len is ambigious: both a per-ring sizing multiplier and a default queue-length/limit knob for consumers that allocate nothing at set time (pfifo/bfifo/gred/plug/sfb limits, htb direct_qlen, qfq max_classes, teql). 32767 is chosen as the largest value NLA_POLICY_FULL_RANGE can express for the u32 IFLA_TXQLEN policy in patch 2/3 while staying a legitimate queue length on high-BDP paths; the ring-memory trade-off of a shared knob is disclosed below. Conditions to recreate the bug: - CONFIG_NET_SCHED=y, CONFIG_VETH=y, CONFIG_USER_NS=y, CONFIG_NET_NS=y. - Unprivileged user in a fresh user+net namespace (unshare -Urn). - pfifo_fast: create veth pairs, set tx_queue_len to 500000, attach mq+pfifo_fast. ~28 iterations OOMs a 2GB guest. - tun: create 50 tun devices with IFF_MULTI_QUEUE, set tx_queue_len to 500000, open 8 queues each. ~1.6GB of ptr_ring allocations OOMs a 512MB guest. - tap: same as tun with IFF_TAP. ~960MB OOMs a 512MB guest. - On the fixed kernel the oversized tx_queue_len is rejected with -ERANGE at set time (all four paths: RTM_SETLINK, RTM_NEWLINK create, sysfs, ioctl - the latter two via this check, the former two via this check and the 2/3 parse policy respectively).
In the Linux kernel, the following vulnerability has been resolved: pds_core: fix cmd_regs access racing BAR unmap on reset pdsc_reset_prepare() and pdsc_reset_done()'s pdsc_map_bars() error path clear/iounmap cmd_regs without devcmd_lock, and pdsc_legacy_firmware_update()'s download loop derefs cmd_regs after dropping and retaking the lock without re-checking. An FLR concurrent with a devlink flash can unmap cmd_regs under an in-flight devcmd, causing a NULL deref or a write to unmapped MMIO. Take devcmd_lock across the BAR unmap/remap, and re-check cmd_regs in the download loop. Only the PF maps cmd_regs and runs devcmd, so skip the unmap on a VF, as pdsc_remove() and pdsc_reset_done() already do. A reset that completes entirely within the unlocked window is not a correctness problem for the image: the device clears its update session, so a resumed download is rejected, and it verifies the staged image before writing a flash slot, reporting PDS_RC_BAD_FW rather than activating it. pdsc_unmap_bars() also clears info_regs, intr_status and intr_ctrl. The interrupt and start/stop readers of those are quiesced before the unmap by pdsc_fw_down(), which frees the interrupts and tears down the queues. The debugfs readers are not, since those files outlive a reset; that is pre-existing and out of scope here.
In the Linux kernel, the following vulnerability has been resolved: net: mctp: i3c: serialize probe with bus removal mctp_i3c_probe() drops busdevs_lock after finding the matching bus. A concurrent I3C_NOTIFY_BUS_REMOVE can then unregister and free the bus netdev before probe passes its private data to mctp_i3c_add_device(). The latter consequently adds a list node through a freed mbus pointer. Keep busdevs_lock held until the device has been added. This also satisfies the __must_hold annotation on mctp_i3c_add_device().
In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix use-after-free race in sample_restore_put() Concurrent teardown of TC sample rules sharing the same restore context may re-read restore->count after dropping restore_lock. At that point another thread may already have completed cleanup and freed the restore object. Use the result of the refcount decrement while holding restore_lock to determine whether cleanup is needed.
In the Linux kernel, the following vulnerability has been resolved: net/mlx5: E-Switch: fix use-after-free in mlx5_eswitch_termtbl_put In mlx5_eswitch_termtbl_put(), the zero-ref cleanup check reads tt->ref_count after termtbl_mutex has been released. Two concurrent callers on the same mlx5_termtbl_handle race: one decrements ref_count to zero, removes the hash entry, and calls kfree(tt) while the other has already dropped the mutex and is about to evaluate if (!tt->ref_count), producing a use-after-free. Fix this by capturing the result of the decrement into a stack-local last variable before dropping the mutex. The cleanup decision is now made entirely under termtbl_mutex, and tt is not touched after kfree.
In the Linux kernel, the following vulnerability has been resolved: net/mlx5: E-Switch, prevent mc_list repopulation during vport disable In mlx5_esw_vport_disable(), move esw_apply_vport_rx_mode() ahead of esw_vport_change_handle_locked() so vport->allmulti_rule is NULL before the change handler observes it. During FW-fatal recovery the disable runs while dev->state == INTERNAL_ERROR. The promisc query inside esw_update_vport_rx_mode() fails and returns early, leaving vport->allmulti_rule intact, so esw_update_vport_mc_promisc() runs and adds MLX5_ACTION_ADD entries to vport->mc_list whose flow rules are then installed in the FDB by esw_add_mc_addr(). esw_destroy_legacy_table() tears down the FDB with those refs still held, corrupting the sub-tree and leaving dangling flow_rule pointers in vport->mc_list. Two-stage failure on `echo 1 > /sys/bus/pci/devices/<bdf>/reset`: refcount_t: underflow; use-after-free. tree_put_node+0xef/0x110 [mlx5_core] clean_tree+0x44/0xd0 [mlx5_core] (x5) mlx5_fs_core_cleanup+0x57/0x1c0 [mlx5_core] mlx5_unload+0x65/0xd0 [mlx5_core] ... mlx5_health_try_recover BUG: unable to handle page fault for address: 0000000003000055 down_write+0x1c/0x60 mlx5_del_flow_rules+0x33/0x1f0 [mlx5_core] esw_del_mc_addr+0x7b/0x170 [mlx5_core] esw_apply_vport_addr_list+0x56/0xf0 [mlx5_core] esw_vport_change_handle_locked+0x28b/0x310 [mlx5_core] mlx5_esw_vport_enable+0x270/0x4a0 [mlx5_core] ... mlx5_load ... mlx5_health_try_recover esw_apply_vport_rx_mode(false, false) clears vport->allmulti_rule via its local state machine even when the FW del fails. With the rule NULL the !IS_ERR_OR_NULL(allmulti_rule) gate in the change handler closes, no rules are installed during disable, and the reload starts with a clean mc_list.
In the Linux kernel, the following vulnerability has been resolved: net/sched: fq_pie: clamp quantum in change path fq_pie_change() accepts any quantum value from userspace, including 1. With a crafted size table qdisc_pkt_len reaches ~2 GiB, so quantum=1 makes the deficit-refill loop spin ~2^31 times under the qdisc lock (a soft lockup / denial of service). Add max(256U, ...) matching fq_codel_change(). Conditions to recreate the bug: CONFIG_NET_SCH_FQ_PIE=y. Requires CAP_NET_ADMIN (namespace-local via unshare -Urn suffices). tc qdisc add dev dummy0 root fq_pie tc qdisc change dev dummy0 root fq_pie quantum 1 stab data 32768 size_log 15 cell_log 0
In the Linux kernel, the following vulnerability has been resolved: net/sched: sfq: clamp quantum in change path sfq_change() accepts any non-negative quantum (only rejects (int)ctl->quantum < 0). With a crafted size table qdisc_pkt_len reaches ~2 GiB, so quantum=1 makes the deficit-refill loop spin ~2^31 times under the qdisc lock (a soft lockup / denial of service). Add max(256U, ...) matching fq_codel_change(). Reject quantum > 1<<20 with -EINVAL, matching fq_codel_change() and the init clamp. Conditions to recreate the bug: CONFIG_NET_SCH_SFQ=y. Requires CAP_NET_ADMIN (namespace-local via unshare -Urn suffices). tc qdisc add dev dummy0 root sfq tc qdisc change dev dummy0 root sfq quantum 1 stab data 32768 size_log 15 cell_log 0
In the Linux kernel, the following vulnerability has been resolved: net/sched: hhf: clamp quantum in change and init paths hhf_change() accepts any quantum from userspace, including 1. With a crafted size table qdisc_pkt_len reaches ~2 GiB, so quantum=1 makes the deficit-refill loop spin ~2^31 times under the qdisc lock (a soft lockup / denial of service). Add max(256U, ...) in hhf_change() matching fq_codel_change(). Clamp hhf_init() to [256, 1<<20] matching the siblings, and remove the old fallback that only set quantum=256 on overflow. Conditions to recreate the bug: CONFIG_NET_SCH_HHF=y. Requires CAP_NET_ADMIN (namespace-local via unshare -Urn suffices). tc qdisc add dev dummy0 root hhf tc qdisc change dev dummy0 root hhf quantum 1 stab data 32768 size_log 15 cell_log 0
In the Linux kernel, the following vulnerability has been resolved: net/sched: drr: clamp quantum in change class drr_change_class() rejects explicit quantum==0 but falls back to psched_mtu() with no floor. With a crafted size table qdisc_pkt_len reaches ~2 GiB, so quantum=1 (or a zero psched_mtu on a headerless device) makes the deficit-refill loop spin under the qdisc lock. Add clamp_t(u32, quantum, 256, 1<<20) after the zero reject and on the fallback path. The explicit-zero reject is preserved. Conditions to recreate the bug: CONFIG_NET_SCH_DRR=y. Requires CAP_NET_ADMIN (namespace-local via unshare -Urn suffices). tc qdisc add dev dummy0 root drr tc class add dev dummy0 parent 1: classid 1:1 drr quantum 1
In the Linux kernel, the following vulnerability has been resolved: net/sched: ets: clamp quantum in parse and fallback paths ets_qdisc_change() falls back to psched_mtu() with no floor for bands without an explicit quantum. With a crafted size table qdisc_pkt_len reaches ~2 GiB, so a zero psched_mtu on a headerless device makes the deficit-refill loop spin under the qdisc lock. Move the floor into ets_quantum_parse() so explicitly configured quanta are also clamped to [256, 1<<20], not just the fallback path. Conditions to recreate the bug: CONFIG_NET_SCH_ETS=y. Requires CAP_NET_ADMIN (namespace-local via unshare -Urn suffices). tc qdisc add dev dummy0 root ets bands 3 strict 2 quanta 1 1
In the Linux kernel, the following vulnerability has been resolved: net: macb: fix NULL pointer dereference on unbind with fixed-link When the device tree describes a fixed-link and has no "mdio" child node, macb_mii_init() returns early without allocating the MDIO bus, leaving bp->mii_bus as NULL. Two cleanup paths then dereference this NULL bus: 1. On driver unbind, macb_remove() unconditionally calls mdiobus_unregister(bp->mii_bus), which oopses: Unable to handle kernel NULL pointer dereference at virtual address 00000000000004a8 pc : mdiobus_unregister+0x14/0xa4 lr : macb_remove+0x38/0xa4 Call trace: mdiobus_unregister+0x14/0xa4 (P) macb_remove+0x38/0xa4 platform_remove+0x20/0x30 device_release_driver_internal+0x1c8/0x224 unbind_store+0xb4/0xbc 2. On the probe error path in macb_probe(), reached when macb_mii_init() has succeeded but a subsequent step fails, the err_out_unregister_mdio label runs the same unconditional cleanup. mdiobus_unregister() and mdiobus_free() do not guard against a NULL bus, so guard the calls in both macb_remove() and the probe error path.
In the Linux kernel, the following vulnerability has been resolved: bpf: Reject non-scalar bpf_loop iteration counts bpf_loop() declares its nr_loops argument as ARG_ANYTHING. Privileged programs may pass pointer values to such arguments, so check_func_arg() lets a pointer-valued R1 reach the helper-specific checks. Since commit bb124da69c47 ("bpf: keep track of max number of bpf_loop callback iterations"), the verifier marks R1 precise and reads its upper bound to limit callback simulation. Precision backtracking only accepts scalar registers, so passing a pointer instead triggers the "backtracking misuse" verifier warning. Kernels with panic_on_warn enabled subsequently panic. Introduce ARG_SCALAR for helper arguments that only accept scalar values and use it for bpf_loop() nr_loops. Generic helper argument validation then rejects pointers before loop inlining and precision processing.
In the Linux kernel, the following vulnerability has been resolved: ALSA: caiaq: Decoupling ep1_in_urb in caiaq dev The epq_in_urb object belonging to the caiaq device is coupled within the struct snd_usb_caiaqdev. After usb_submit_urb(epq_in_urb, GFP_KERNEL) executes successfully, epq_in_urb is successfully added to the urbp_list queue of the dummy HCD driver (userspace specifies dummy_hcd as the HCD layer driver for the caiaq USB device). When init_card() calls snd_usb_caiaq_send_command() which subsequently fails due to a timeout, and proceeds to call snd_card_free() to release the card, the embedded ep1_in_urb object is also freed. When the dummy HCD driver detects that the URB has been unlinked, it returns the URB (by usb_hcd_giveback_urb()), which triggers [1]. Decouple the ep1_in_urb object from the struct snd_usb_caiaqdev and switch to using a pointer instead. Separately allocate and manage the memory for ep1_in_urb to prevent the release of the snd_card memory object from interfering with it. midi_out_urb has the same issue as ep1_in_urb and is handled in the same way. [1] BUG: KASAN: slab-use-after-free in usb_free_urb+0x24/0x120 drivers/usb/core/urb.c:96 Write of size 4 at addr ffff88803cee1050 by task ktimers/1/29 Call Trace: usb_free_urb+0x24/0x120 drivers/usb/core/urb.c:96 dummy_timer+0xaac/0x4d50 drivers/usb/gadget/udc/dummy_hcd.c:2019 __run_hrtimer kernel/time/hrtimer.c:2067 [inline] __hrtimer_run_queues+0x3eb/0xaf0 kernel/time/hrtimer.c:2124 hrtimer_run_softirq+0x1e1/0x2e0 kernel/time/hrtimer.c:2141 Allocated by task 36: snd_card_new+0x7b/0x110 sound/core/init.c:184 create_card sound/usb/caiaq/device.c:429 [inline] snd_probe+0x236/0x1af0 sound/usb/caiaq/device.c:544 Freed by task 36: snd_card_free_when_closed sound/core/init.c:630 [inline] snd_card_free+0x138/0x1d0 sound/core/init.c:662 snd_probe+0x162b/0x1af0 sound/usb/caiaq/device.c:553
In the Linux kernel, the following vulnerability has been resolved: hwmon: (ltc4282) Make sure clk_init_data is fully initialized The clk_init_data structure contains several mutually-exclusive members for different methods to specify the possible parents of a clock, prompting drivers to initialize only the members they need. However, not initializing all members may cause subtle issues, which are only exposed when CONFIG_INIT_STACK_ALL_PATTERN or CONFIG_INIT_STACK_NONE is enabled. ltc428_clk_provider_setup() does not fill in any parent clocks, and assumes that init.num_parents is NULL. However, the latter in uninitialized, and thus may cause a crash. Make sure all members are fully initialized, to fix such bugs, and to avoid future breakage when converting drivers to a different method for specifying the parents.
In the Linux kernel, the following vulnerability has been resolved: virtio: fix use-after-free in unregister_virtio_device() device_unregister() is device_del() plus put_device(). When the caller holds no extra reference, that drops the last one and runs the release callback, which for several transports frees the memory the embedded struct virtio_device sits in. unregister_virtio_device() then calls virtio_debug_device_exit(), which reads dev->debugfs_dir out of the freed object. Affected transports are the ones whose release callback frees and whose remove path takes no reference: virtio_mmio, virtio_vdpa, virtio_uml, mlxbf-tmfifo and virtio_ccw. virtio_pci is unaffected because virtio_pci_remove() brackets the call with get_device() and put_device(). Remove the debugfs entries before the device can go away. They are only accessed through the protected debugfs interface, so debugfs_remove_recursive() waits for in-progress file operations before returning. Tearing them down while the device is still alive is therefore safe. Reproduced on User-Mode Linux with CONFIG_KASAN and CONFIG_VIRTIO_DEBUG by unbinding a virtio-uml device: BUG: KASAN: slab-use-after-free in virtio_debug_device_exit+0x36/0x4d Read of size 8 at addr 00000000616e0b10 by task init/1 __asan_report_load8_noabort virtio_debug_device_exit+0x36/0x4d unregister_virtio_device+0x48/0x75 virtio_uml_remove platform_remove device_release_driver_internal unbind_store Freed by task 1: kfree virtio_uml_release_dev device_release kobject_put put_device device_unregister With this applied, the report is gone and unbind is clean.
In the Linux kernel, the following vulnerability has been resolved: virtio_console: do not free control-out buffers on remove __send_control_msg() publishes &portdev->cpkt as the control-out virtqueue cookie. remove_vqs() walks every virtqueue and passes leftover cookies to free_buf(), which treats them as struct port_buffer and reads sgpages. If a control message is still on c_ovq when the device is unbound, free_buf() reads past the ports_device object. KASAN reported slab-out-of-bounds in free_buf(): free_buf remove_vqs virtcons_remove unbind_store The object was the ports_device allocated in virtcons_probe(). Drain c_ovq without freeing. The packet lives in portdev and is released with it.
In the Linux kernel, the following vulnerability has been resolved: virtio_input: reset device if input_register_device() fails Probe marks the device DRIVER_OK with virtio_device_ready() before calling input_register_device(). If registration fails, the error path cleared vi->ready and called del_vqs() while the device was still live, so the device could keep DMA to queues that were already torn down. Match remove/freeze: call virtio_reset_device() on that path before tearing down the virtqueues.
In the Linux kernel, the following vulnerability has been resolved: virtio_input: stop callbacks before unregistering input device virtinput_remove() unregisters the input device before resetting the virtio device. virtinput_recv_events() drops vi->lock around input_event(), so clearing vi->ready does not stop a callback that passed the entry check. It can still use vi->idev, requeue buffers and kick the queue. Reset first, as virtinput_freeze() already does. With the preceding core change, reset waits for callbacks before input_unregister_device() can free vi->idev. Recheck vi->ready after taking the lock again: keep draining completed events so an input packet is not truncated, but stop requeueing buffers and kicking the queue. With evdev attached, input_unregister_handle() currently waits for an RCU grace period, which also waits out IRQ callbacks. This masks the lifetime bug on PCI and MMIO, but does not protect sleepable callbacks on other transports.
In the Linux kernel, the following vulnerability has been resolved: af_unix: Update last skb marker in manage_oob(). Fahad Alharbi reported that blocking recv(MSG_PEEK) could hog CPU due to OOB skb. In the following cases, manage_oob() skips OOB skb(s) and returns NULL for the last recv(MSG_PEEK): socketpair(AF_UNIX, SOCK_STREAM, 0, sk); 1) skb -> OOB skb -> NULL send(sk[0], "ab", 2, MSG_OOB); recv(sk[1], buf, 0, MSG_PEEK); 2) skb -> consumed OOB skb -> NULL send(sk[0], "ab", 2, MSG_OOB); recv(sk[1], buf, 1, MSG_OOB); recv(sk[1], buf, 0, MSG_PEEK); 3) consumed OOB skb -> OOB skb -> NULL send(sk[0], "a", 1, MSG_OOB); recv(sk[1], buf, 0, MSG_OOB); send(sk[0], "b", 1, MSG_OOB); recv(sk[1], buf, 1, MSG_PEEK); Then, @copied is 0 in unix_stream_read_generic() (zero-length buffer, or non-OOB skb is not yet consumed), and unix_stream_data_wait() is called. However, it returns immediately because @last is not updated in unix_stream_read_generic(), and the thread busy-waits for a new skb. Let's update @last in manage_oob(). For MSG_PEEK, @last is updated with the skipped OOB, and for the non-peek case, @last matches the returned value (when !copied) because OOB is unlinked. Note that manage_oob() is inlined and no stack canary is added.
In the Linux kernel, the following vulnerability has been resolved: net: ipv6: Fix UDP length overflow with PMTU discover and big MTU This commit bounds cork->base.fragsize to IP6_MAX_MTU for UDP sockets to avoid a possible overflow of UDP length that triggers a WARN in udp_set_len_short when setsockopt IPV6_MTU_DISCOVER is set to IPV6_PMTUDISC_DO or IPV6_PMTUDISC_PROBE, and a large packet is sent over a netdev with an unusually large MTU. Steps to reproduce (included in the new selftest): 1. Set device MTU bigger than IP6_MAX_MTU. cork->base.fragsize will be set to that MTU in ip6_setup_cork. 2. Set IPV6_MTU_DISCOVER to IPV6_PMTUDISC_PROBE or IPV6_PMTUDISC_DO. It lets maxnonfragsize be set to device MTU (cork->fragsize) in __ip6_append_data, rather than to IP6_MAX_MTU. 3. Send 65528 bytes of payload (+8 bytes of UDP header, +40 bytes of IPv6 header). Device MTU allows it (it's only one byte bigger than IP6_MAX_MTU, and the device MTU is bigger than that). 4. The UDP length in the built packet is 65536, which overflows the 16-bit length field and triggers the WARN in udp_set_len_short. To avoid breaking sending UDP jumbograms over raw IPv6 sockets, limit the change to UDP sockets only. The original overflow bug with IPv6 and IPV6_PMTUDISC_DO seems to predate git history (verified reproduction on 2.6.21), was fixed later, and then reappeared in commit 427faee167bc ("net: ipv6: introduce ip6_dst_mtu_maybe_forward"), which is chosen as the Fixes tag here. The overflow with IPV6_PMTUDISC_PROBE reproduces since its introduction in commit 628a5c561890 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE").
In the Linux kernel, the following vulnerability has been resolved: net: ethernet: cortina: Fix budget accounting The gmac_rx() function returns the remaining NAPI budget, but its caller treats the return value as the number of packets received. An idle poll therefore reports a full budget and remains scheduled. Return the number of received packets instead. Preserve the existing free queue refill accounting by adding that count directly; continuing to subtract it from the budget would invert the refill behavior.
In the Linux kernel, the following vulnerability has been resolved: net: ethernet: cortina: Count dropped frames as NAPI work The RX loop only consumes budget when it successfully delivers a frame. Error paths keep consuming descriptors without reducing the budget, so a stream of bad frames can process the entire receive ring in one poll. Move the budget accounting to a common end-of-frame path. This counts each completed frame as NAPI work whether it was delivered or dropped, matching the behavior of the vendor driver.
In the Linux kernel, the following vulnerability has been resolved: ice: add missing xa_destroy for sched_node_ids Commit 16dfa49406bc ("ice: Introduce new parameters in ice_sched_node") added a sched_node_ids xarray to the port info structure, but never called xa_destroy on it. Since xarrays can allocate internal memory, this can result in a memory leak even if every element in the xarray has been removed. The xarray is currently embedded in the port_info structure. This appears to have been done because its use is within functions that take the port_info as a primary argument. However, this complicates managing the lifecycle of the field. The port_info structure is allocated in ice_init_hw() using devm, and it is not released until the devm cleanup when the driver is unloaded. The ice_init_hw() function is called in many places, including devlink reload, and possibly during DDP load after updating the Tx scheduler layout. Adding a call of xa_destroy to the ice_deinit_hw() causes Sashiko to raise multiple concerns due to potential ordering issues and possible ways that port_info could be a dangling reference. To handle this, move the sched_node_ids out of port_info and into the hw structure. All users of the array already have a pointer to hw anyways, and there is only one sched_node_ids per adapter. While here, remove the overly verbose comment explaining the nature of the sched_node_ids xarray. Add the missing xa_destroy to the cleanup path and to ice_deinit_hw(), ensuring that we properly release the xarray memory. This was caught by Sashiko during development of unrelated code.
In the Linux kernel, the following vulnerability has been resolved: eth: ice: don't dereference pointers from TP_printk() After forwarding net-next during the v7.3 merge window we started seeing: TRACE EVENT ERROR: Event ice_tx_dim_work has double dereference in TP_printk: REC->q_vector->tx.tx_ring->q_index WARNING: kernel/trace/trace_events.c:420 at test_double_dereference.cold+0x39/0x4b this is due to extra checks added in tracing subsystem in commit b5cc230af5e5 ("tracing: Warn when an event dereferences a pointer in TP_printk()"). Printing happens long after the event was recorded, by which point the pointers may be invalid (the ring or the dim instance). Copy the eight scalars into the event instead.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: Fix UAF of btusb_data by rx_work btusb_close() and btusb_flush() cancel data->rx_work with the asynchronous cancel_delayed_work(), so if btusb_rx_work() is already running on another CPU it keeps running after the cancel returns. btusb_disconnect() calls hci_unregister_dev(), which invokes btusb_close(), and then frees the btusb_data. A still running btusb_rx_work() then dereferences the freed data: while ((skb = skb_dequeue(&data->acl_q))) data->recv_acl(data->hdev, skb); Use cancel_delayed_work_sync() instead. In btusb_close() the cancel also has to happen after btusb_stop_traffic(), otherwise an URB completion racing with the cancel can requeue the work right after it has been waited for.
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btintel_pcie: validate packet_len before skb_put_data btintel_pcie_submit_rx_work() reads packet_len from rfh_hdr without checking if it exceeds the RX buffer size. An oversized packet_len can lead to an out-of-bounds read in skb_put_data(). Validate packet_len to ensure it is non-zero and does not exceed BTINTEL_PCIE_BUFFER_SIZE - sizeof(*rfh_hdr), logging an error when invalid. This issue was reported by Claude Mythos. It can be simulated either by using customized firmware configured to return an invalid packet_len or by modifying rfh_hdr->packet_len in the driver before calling btintel_pcie_submit_rx_work().
In the Linux kernel, the following vulnerability has been resolved: net: macb: destroy the phylink instance on the probe error path macb_mii_init() creates a phylink instance on both of its success paths, but the probe unwind frees the netdev without destroying it, so a failing macb_alloc_tieoff() or register_netdev() leaks the instance. Destroy it at err_out_unregister_mdio, which is only reachable once macb_mii_init() has succeeded, so bp->phylink is valid there.
In the Linux kernel, the following vulnerability has been resolved: watchdog: msc313e: Avoid division by zero clk_get_rate() could return 0. Avoid a division by zero panic.
In the Linux kernel, the following vulnerability has been resolved: watchdog: msc313e: Fix clock leak and spurious timer in settimeout() msc313e_wdt_settimeout() unconditionally calls msc313e_wdt_start() which introduces two severe bugs: 1. If the watchdog is already active, calling start() again will increase the reference count of the clock again. However stop() is only called once, the reference count is unbalance. 2. If the watchdog is stopped, calling settimeout() will start the hardware timer accidentally. Factor out the register-writing logic into a helper function. Only call it in settimeout() if the watchdog is running. Otherwise, simply update `wdev->timeout`.
In the Linux kernel, the following vulnerability has been resolved: hwmon: (corsair-cpro) Create debugfs entries after hwmon registration ccp_debugfs_init() registers debugfs files whose private data is the devm allocated ccp. It runs before hwmon_device_register_with_info(), so when that registration fails, ccp_probe() returns with the files still in place. The HID core then frees ccp, and ccp_remove() is not called for a failed probe, so nothing removes them later either. Reading one of the files dereferences the freed pointer. Create the debugfs entries only after the hwmon device has been registered, so no failing path can leave them behind. The two version queries stay where they are. They send USB commands without holding ccp->mutex, which is only safe as long as nothing else can call send_usb_cmd(); once the hwmon device is registered its callbacks can do so concurrently. Only the debugfs creation moves, and it is told which queries succeeded.
In the Linux kernel, the following vulnerability has been resolved: vxlan: initialize _md in vxlan_xmit_one() If a VXLAN device is configured with both VXLAN_F_COLLECT_METADATA and VXLAN_F_GBP, and a packet is transmitted through it using an external ip_tunnel_info that lacks the IP_TUNNEL_VXLAN_OPT_BIT flag, md is left pointing to the uninitialized _md stack variable: if (test_bit(IP_TUNNEL_VXLAN_OPT_BIT, info->key.tun_flags)) { if (info->options_len < sizeof(*md)) goto drop; md = ip_tunnel_info_opts(info); } Because IP_TUNNEL_VXLAN_OPT_BIT is not set, md is not updated and remains pointing to _md. Later, vxlan_build_skb() is called with md, which eventually calls vxlan_build_gbp_hdr(): if (vxflags & VXLAN_F_GBP) vxlan_build_gbp_hdr(vxh, md); Inside vxlan_build_gbp_hdr(), md->gbp is read: if (!md->gbp) return; gbp = (struct vxlanhdr_gbp *)vxh; ... if (md->gbp & VXLAN_GBP_DONT_LEARN) gbp->dont_learn = 1; If the stack contains garbage, this causes: 1) VXLAN_HF_GBP flag to be spuriously set in the VXLAN header. 2) gbp->dont_learn and gbp->policy_applied to be set from stack bits. 3) gbp->policy_id to receive 16 bits of uninitialized kernel stack data, leaking it onto the wire. Fix this by zero-initializing _md. If IP_TUNNEL_VXLAN_OPT_BIT is not present, md->gbp remains 0, and vxlan_build_gbp_hdr() returns early without modifying the VXLAN header.
In the Linux kernel, the following vulnerability has been resolved: ppp_synctty: ensure a writeable skb header ppp_sync_txmunge() checks headroom before prepending the address and control bytes, but does not ensure that the skb header is writable. A received skb can reach this function through PPP channel bridging without passing through ppp_start_xmit(), which calls skb_cow_head(). For example, a PPPoE frame may share its buffer with a clone queued to an AF_PACKET socket. If it is bridged to a synchronous tty channel, the address/control bytes can overwrite data still visible to that socket. Use skb_cow_head() to ensure both sufficient headroom and a writable header.
In the Linux kernel, the following vulnerability has been resolved: net: stmmac: initialize ptp_lock at probe time priv->ptp_lock is only initialized in stmmac_ptp_register(), which runs during __stmmac_open(). However, the lock is also used while the interface is down and has never been opened: tc_taprio_configure() invokes the PTP gettime64() callback to compute the EST base time when offloading a TAPRIO schedule, and stmmac_get_time() takes priv->ptp_lock. Using an uninitialized rwlock is undefined behaviour. Move the rwlock_init() to __stmmac_dvr_probe(), together with the other private locks, so that ptp_lock is always valid regardless of the interface state.
In the Linux kernel, the following vulnerability has been resolved: perf/core: Allow list_del during perf_event_overflow() A PMU might use perf_sched_cb_inc() and perf_sched_cb_dec() interface to get the PMU call back function pmu::sched_task invoked at schedule in and schedule out. This is achieved by walking along the list anchored by sched_cb_list. The following scenario might lead to a list corruption. perf_pmu_sched_task() for_each_list_entry(..., &sched_cb_list) +--> __perf_pmu_sched_task() +--> event->pmu->sched_task()) +--> PMU_push_sample() +--> perf_event_overflow() +--> __perf_event_overflow() +--> pmu->stop() +--> perf_sched_cb_dec() remove entry from sched_cb_list while list node in use. This happens when ioctl(fd, PERF_EVENT_IOC_REFRESH, xxx) has been invoked and perf_event::event_limit hits zero. Prevent the list corruption and convert for_each_list_entry() to for_each_list_entry_safe().