In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: bound aligned TLV advance in FW parser Validate ALIGN(tlv_len, 4) against remaining parser length before consuming bytes from the firmware image. This avoids length underflow on malformed TLVs.
In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: acpi: validate WGDS table revision index Check tbl_rev bounds before BIT(tbl_rev) to avoid undefined shifts when firmware reports an invalid revision value.
In the Linux kernel, the following vulnerability has been resolved: cifs: validate idmap key payload length The cifs.idmap key type stores its payload length in key->datalen, which is limited to U16_MAX. Accepting a larger key payload truncates the recorded length and can make later users interpret the payload using inconsistent bounds. Reject oversized preparsed payloads before allocating or copying them. This keeps key->datalen consistent with the stored data for both inline and separately allocated idmap payloads.
In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: validate IEs in cfg80211_wext_siwgenie() The KASAN allocation trace shows that a malformed IE buffer is stored via SIOCSIWGENIE (cfg80211_wext_siwgenie()) without any validation. The crash trace shows that a subsequent SIOCSIWESSID triggers a connection attempt which calls cfg80211_sme_get_conn_ies() to process the stored IE buffer, causing: - An out-of-bounds read in skip_ie() which reads ies[pos+1] (the length byte) past the end of the 1-byte buffer. - An integer underflow in the memcpy size argument when offs returned by ieee80211_ie_split() exceeds ies_len, causing unsigned subtraction to wrap to SIZE_MAX and triggering a fortify panic. Fix this by validating the IE buffer in cfg80211_wext_siwgenie() before storing it. [drop unnecessary ie_len check, update commit message]
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: validate skb length in rfcomm_recv_frame rfcomm_recv_frame() casts skb->data to struct rfcomm_hdr and dereferences hdr->addr and hdr->ctrl without validating skb->len first. A truncated frame with skb->len less than the minimum header size causes an out-of-bounds read of uninitialized memory. Additionally, a zero-length frame causes skb->len-- to underflow to UINT_MAX, making skb_tail_pointer() read far past the buffer. Commit 23882b828c3c ("Bluetooth: RFCOMM: validate skb length in MCC handlers") fixed the same class of missing-length-check bugs in the MCC sub-handlers, but the top-level rfcomm_recv_frame() was left unfixed. KMSAN reports: BUG: KMSAN: uninit-value in rfcomm_run ... Uninit was created at: __alloc_skb+0x474/0xb60 vhci_write+0xe9/0x870 Fix this by rejecting frames smaller than sizeof(struct rfcomm_hdr) + 1 (the minimum frame must have a 3-byte header and a 1-byte FCS).
In the Linux kernel, the following vulnerability has been resolved: scsi: core: Do not block on tag allocation in scsi_eh_lock_door() scsi_eh_lock_door() is called from scsi_restart_operations() while the host is still in the SHOST_RECOVERY state, i.e. before the host is switched back to SHOST_RUNNING and scsi_run_host_queues() restarts the queues. It allocates a request via scsi_alloc_request() with no flags, so blk_mq_get_tag() may block waiting for a free sched tag when all tags are already in use. Those tags can be held by commands that were just requeued by scsi_eh_flush_done_q() during error handling. Such commands cannot be dispatched until the host leaves SHOST_RECOVERY and scsi_run_host_queues() is called - which only happens *after* scsi_eh_lock_door() returns. This forms a circular dependency: - scsi_eh_lock_door(), running in the SCSI error handler thread, waits for a sched tag held by a requeued command; - the requeued command cannot complete and release its sched tag until the error handler thread leaves scsi_restart_operations() and restart the queues. For devices with a single driver tag (e.g. USB storage) it is a guaranteed deadlock and I/O that can never be submitted. This problem has also been reproduced in our environment. Locking the door is a best-effort operation, and scsi_eh_lock_door() already returns silently when the request allocation fails. Pass BLK_MQ_REQ_NOWAIT to scsi_alloc_request() so the allocation fails instead of blocking when no tag is available. This breaks the circular dependency and allows the error handler to finish restarting the queues, after which the pending commands are dispatched normally.
In the Linux kernel, the following vulnerability has been resolved: net: appletalk: fix NULL pointer dereference in aarp_send_ddp() aarp_send_ddp() calls atalk_find_dev_addr(dev) in the LocalTalk fast path without checking for NULL. When the device has no AppleTalk interface configured (dev->atalk_ptr == NULL), this leads to a NULL pointer dereference at the at->s_net access. KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:aarp_send_ddp (net/appletalk/aarp.c:552 (discriminator 2)) Call Trace: <TASK> atalk_sendmsg (net/appletalk/ddp.c:1715) __sys_sendto (net/socket.c:2265 (discriminator 1)) __x64_sys_sendto (net/socket.c:2272) do_syscall_64 (arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) Add a NULL check consistent with the other callers of atalk_find_dev_addr().
In the Linux kernel, the following vulnerability has been resolved: f2fs: embed f2fs_gc_kthread in f2fs_sb_info Instead of allocating f2fs_gc_kthread dynamically, embed it in f2fs_sb_info. This simplifies lifetime management and prepares for fixing race conditions during teardown. - __sbi_store - remount|shutdown - f2fs_stop_gc_thread - access sbi->gc_thread - sbi->gc_thread = NULL - access sbi->gc_thread->f2fs_gc_task
In the Linux kernel, the following vulnerability has been resolved: lockd: fix swapped arguments in nlmsvc_match_ip() When releasing locks by server IP address via /proc/fs/nfsd/unlock_ip, nlmsvc_unlock_all_by_ip() calls nlm_traverse_files() with the server sockaddr as the opaque @data argument: nlm_traverse_files(server_addr, nlmsvc_match_ip, NULL); The match callback is later invoked from nlm_traverse_locks() as: match(lockhost, host); where the first argument is the nlm_host that owns the lock, and the second argument is the @data that was originally passed down (here the server sockaddr). This is the convention every other match callback relies on (nlmsvc_mark_host(), nlmsvc_same_host(), nlmsvc_is_client()): arg1 is the real nlm_host, arg2 is the caller-supplied reference value. nlmsvc_match_ip() has had these two arguments reversed ever since the unlock-by-IP feature was introduced in commit 4373ea84c84d ("lockd: unlock lockd locks associated with a given server ip"): return rpc_cmp_addr(nlm_srcaddr(host), datap); Here @host is actually the server sockaddr, so nlm_srcaddr(host) dereferences a struct sockaddr as a struct nlm_host and reads garbage at the offset of h_srcaddr; meanwhile @datap is actually the lock owner's nlm_host but is compared as a sockaddr. As a result the comparison practically never matches and locks are not released for the requested IP. Swap the arguments so the lock owner's source address is compared against the requested server address: return rpc_cmp_addr(nlm_srcaddr(datap), (struct sockaddr *)host); [ cel: fix the misleading typedef parameter names too ]
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/ras: add ras_suspend callback and use it for cp_ecc_error_irq cp_ecc_error_irq is acquired in amdgpu_gfx_ras_late_init() but released in gfx_v9_0_hw_fini(), so the put site has to query amdgpu_irq_enabled() because the get is skipped on SR-IOV VF. ras_late_init / ras_fini have no suspend counterpart, so move the put to amdgpu_gfx_ras_suspend() / amdgpu_gfx_ras_fini() and add a matching ras_suspend callback that is invoked from amdgpu_ras_suspend() before disable_all_features(). The get and put now sit in the same place and check the same condition (not VF, funcs registered), no refcount querying needed. An active flag gates ras_fini so the suspend-then-unload-without-resume path falls into amdgpu_ras_block_late_fini_default() instead of double-releasing what ras_suspend already cleaned up. Drop the cp_ecc_error_irq put from gfx_v9_0_hw_fini(). gfx_v8_0 manages cp_ecc_error_irq locally and is unaffected; no other GFX generation has this IRQ.
In the Linux kernel, the following vulnerability has been resolved: gfs2: fix quota init duplicate scan gfs2_quota_init() checks for duplicate quota_change IDs while holding qd_lock and the quota hash bucket bitlock. That path used gfs2_qd_search_bucket(), which takes a lockref reference via lockref_get_not_dead(). On PREEMPT_RT this may sleep, which is not allowed under the bucket bitlock, triggering "sleeping function called from invalid context". Use a no-ref bucket lookup in this path, then continue duplicate handling without taking a lockref there. Refactor gfs2_qd_search_bucket() to build on top of the no-ref helper so lookup traversal stays in one place. This patch fixes a bug reported by syzbot.
In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: reject duplicate wiphy cipher suite entries Duplicate entries in wiphy->cipher_suites do not describe any additional capability, but cfg80211 currently accepts them and leaves individual consumers to deal with them. One such consumer is the WEXT compatibility code, which appends a WEP key length for each WEP cipher entry it sees. Repeated WEP entries can therefore overflow the fixed iw_range::encoding_size array returned by SIOCGIWRANGE. Reject duplicate cipher suite entries in wiphy_register() instead. This keeps the cipher suite invariant in one place and makes malformed wiphy descriptions fail early with -EINVAL, rather than relying on a single cfg80211 user to handle duplicates correctly.
In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: reject beacons with bad HE operation The HE operation element not only needs to be longer than the fixed part, but also have an appropriate size for the variable part inside of it. Check this.
In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: Add NULL check for chip->edcca_th in rtw_fw_adaptivity_result() It was recently reported that rtw_fw_adaptivity_result() in fw.c dereferences rtwdev->chip->edcca_th without a NULL check. The issue is that devices with the 8821CE chip don't define edcca_th in their chip info. As a result, when rtw_fw_adaptivity_result() tries to dereference it, the kernel triggers an oops. Add a NULL check for edcca_th before dereferencing it in rtw_fw_adaptivity_result() in fw.c. Placing the check at the function entry avoids logging any garbage values. This change does not address the root cause for this behavior, but it prevents the NULL dereference and the resulting oops while a more permanent solution is developed. Tested on a 8822CE chip which defines edcca_th, so this issue is not present on it, but it still uses this driver and I can verify there are no regressions.
In the Linux kernel, the following vulnerability has been resolved: media: chips-media: wave5: Fix Reports from Kernel Lock Validator handle_dynamic_resolution change requires that the state_lock be acquired based on the lockdep_assert_held. However, the handle_dynamic_resolution_change call in initialize_sequence does not properly obtain the lock before calling. Since the v4l2_ctrl_find and s_ctrl can sleep, they should not be called while a lock is already held. Store off the fbc_buf_count then properly update control once lock has been freed.
In the Linux kernel, the following vulnerability has been resolved: spi: spi-qcom-qspi: Fix incomplete error handling in runtime PM The runtime PM functions had incomplete error handling that could leave the system in an inconsistent state. If any operation failed midway through suspend or resume, some resources would be left in the wrong state while others were already changed, leading to potential clock/power imbalances. Reorder the suspend/resume sequences to avoid brownout risk by ensuring the performance state is set appropriately before clocks are enabled and clocks are disabled before dropping the performance state. Fix by adding proper error checking for all operations and using goto-based cleanup to ensure all successfully acquired resources are properly released on any error.
In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Release request if tb_cfg_request() fails in __tb_xdomain_response() If tb_cfg_request() fails setting up the request (for example the control channel is shut down already) it returns an error without calling the callback. To avoid leaking that memory, call tb_cfg_request_put() if tb_cfg_request() fails.
In the Linux kernel, the following vulnerability has been resolved: media: dm1105: fix missing error check for dma_alloc_coherent The return value of dm1105_dma_map(), which handles DMA memory allocation, is ignored in dm1105_hw_init(). If dma_alloc_coherent() fails, the driver will proceed using a NULL pointer for DMA transfers, leading to a kernel oops or invalid hardware access. Fix this by checking the return value and propagating -ENOMEM on failure.
In the Linux kernel, the following vulnerability has been resolved: crypto: ixp4xx - fix buffer chain unwind on allocation failure chainup_buffers() builds a linked list of buffer descriptors for a scatterlist. If dma_pool_alloc() fails while constructing the list, the current code sets buf to NULL and later dereferences it unconditionally at the end of the function: buf->next = NULL; buf->phys_next = 0; This can lead to a null-pointer dereference on allocation failure. If the failure happens after part of the descriptor chain has already been allocated and DMA-mapped, the partially constructed chain also needs to be released. Fix this by terminating the partially constructed chain on allocation failure and letting the callers unwind it via their existing cleanup paths. Also fix ablk_perform() to preserve the hook pointers before checking for failure, so partially built chains can be freed correctly.
In the Linux kernel, the following vulnerability has been resolved: PCI/sysfs: Add CAP_SYS_ADMIN check to __resource_resize_store() Currently, the __resource_resize_store() allows writing to the resourceN_resize sysfs attribute to change a BAR's size without checking for capabilities, currently relying only on the file access check. Resizing a BAR modifies PCI device configuration and can disrupt active drivers. After the upcoming conversion to static attributes, it will also trigger resource file updates via sysfs_update_groups(). Add a CAP_SYS_ADMIN check to prevent unprivileged users from performing BAR resize operations.
In the Linux kernel, the following vulnerability has been resolved: watchdog: lenovo_se10_wdt: Fix use-after-free and resource leak risk Review by sashiko.dev highlighted potential use after free and resource leak instances. Set se10_pdev to null to prevent use after free Remove DMI call back and instead directly call se10_create_platform_device. Handle error cases appropriately
In the Linux kernel, the following vulnerability has been resolved: mmc: davinci: avoid NULL deref of host->data in IRQ handler mmc_davinci_irq() returns early only when both host->cmd and host->data are NULL: if (host->cmd == NULL && host->data == NULL) { ... return IRQ_NONE; } So we may legitimately reach the rest of the handler with host->data == NULL (and therefore data == NULL). The DATDNE branch already guards against this with an explicit "if (data != NULL)" check, but the subsequent TOUTRD ("read data timeout") and CRCWR/CRCRD ("data CRC error") branches dereference data unconditionally: if (qstatus & MMCST0_TOUTRD) { data->error = -ETIMEDOUT; <-- NULL deref ... davinci_abort_data(host, data); } if (qstatus & (MMCST0_CRCWR | MMCST0_CRCRD)) { data->error = -EILSEQ; <-- NULL deref ... } If either bit is set in qstatus while host->data is NULL, the kernel will crash inside the IRQ handler. smatch flags this: drivers/mmc/host/davinci_mmc.c:933 mmc_davinci_irq() error: we previously assumed 'data' could be null (see line 914) Gate both branches on a non-NULL data, matching the existing pattern used by the DATDNE branch. No functional change for callers where data is non-NULL, which is the only case in which these branches did meaningful work before this change.
In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: phy: check length before parsing PHY status IE Hardware might report PHY status IE with unexpected length, and parser might access out of range. Check the length ahead.
In the Linux kernel, the following vulnerability has been resolved: coresight: perf: Retrieve path and source from event data ETM perf callbacks currently use the per-CPU csdev_src pointer, which can race with updates during device registration and unregistration. The AUX setup already builds and stores the path in the event data. Use this path to retrieve the source instead of csdev_src to avoid the race. Export coresight_get_source() and add etm_event_get_ctxt_path() to retrieve the context's path and its source with READ_ONCE() / WRITE_ONCE() accessors. Give the comments to explain why this approach is safe when pause or resume callbacks preempt the disable callback (e.g. via NMI).
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/userq: pin mqd and fw object bo to avoid eviction mqd and fw objects are queue core objects which should remain valid and never be unmapped and evicted for user queues to work properly. During eviction if these buffers are evicted the hw continue to use the invalid addresses and caused page faults and system hung.
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Bound GPIO I2C table entry count from VBIOS Reject undersized tables and cap the derived entry count to AMDGPU_MAX_I2C_BUS so we do not overrun adev->i2c_bus[] or walk an absurd number of entries on corrupt size fields.
In the Linux kernel, the following vulnerability has been resolved: tty: serial: 8250: protect against NULL uart->port.dev in register serial8250_register_8250_port() conditionally copies uart->port.dev from up->port.dev only when up->port.dev is non-NULL: if (up->port.dev) { uart->port.dev = up->port.dev; ... } So if both the existing uart slot and up have a NULL ->dev, uart->port.dev remains NULL. The very next ACPI companion check then dereferences it unconditionally: if (!has_acpi_companion(uart->port.dev)) { has_acpi_companion() reads dev->fwnode without a NULL guard (include/linux/acpi.h), so this NULL-derefs the kernel for the remaining no-dev case rather than just skipping the mctrl_gpio_init() initialisation as intended. smatch flags the inconsistency: drivers/tty/serial/8250/8250_core.c:767 serial8250_register_8250_port() error: 'uart->port.dev' could be null (see line 719) Guard the call with a NULL check so register continues to work for callers that legitimately have no parent device (legacy non-OF/non-ACPI registrations). No functional change for callers that pass a non-NULL ->dev.
In the Linux kernel, the following vulnerability has been resolved: driver core: Avoid warning when removing a device while its supplier is unbinding During driver removal, the following warning can appear: WARNING: CPU: 1 PID: 139 at drivers/base/core.c:1497 __device_links_no_driver+0xcc/0xfc ... Call trace: __device_links_no_driver+0xcc/0xfc (P) device_links_driver_cleanup+0xa8/0xf0 device_release_driver_internal+0x208/0x23c device_links_unbind_consumers+0xe0/0x108 device_release_driver_internal+0xec/0x23c device_links_unbind_consumers+0xe0/0x108 device_release_driver_internal+0xec/0x23c device_links_unbind_consumers+0xe0/0x108 device_release_driver_internal+0xec/0x23c driver_detach+0xa0/0x12c bus_remove_driver+0x6c/0xbc driver_unregister+0x30/0x60 pci_unregister_driver+0x20/0x9c lan966x_pci_driver_exit+0x18/0xa90 [lan966x_pci] This warning is triggered when a consumer is removed because the links status of its supplier is not DL_DEV_DRIVER_BOUND and the link flag DL_FLAG_SYNC_STATE_ONLY is not set. The topology in terms of consumers/suppliers used was the following (consumer ---> supplier): i2c -----------> OIC ----> PCI device | ^ | | +---> pinctrl ---+ When the PCI device is removed, the OIC (interrupt controller) has to be removed. In order to remove the OIC, pinctrl and i2c need to be removed and to remove pinctrl, i2c need to be removed. The removal order is: 1) i2c 2) pinctrl 3) OIC 4) PCI device In details, the removal sequence is the following (with 0000:01:00.0 the PCI device): driver_detach: call device_release_driver_internal(0000:01:00.0)... device_links_busy(0000:01:00.0): links->status = DL_DEV_UNBINDING device_links_unbind_consumers(0000:01:00.0): 0000:01:00.0--oic link->status = DL_STATE_SUPPLIER_UNBIND call device_release_driver_internal(oic)... device_links_busy(oic): links->status = DL_DEV_UNBINDING device_links_unbind_consumers(oic): oic--pinctrl link->status = DL_STATE_SUPPLIER_UNBIND call device_release_driver_internal(pinctrl)... device_links_busy(pinctrl): links->status = DL_DEV_UNBINDING device_links_unbind_consumers(pinctrl): pinctrl--i2c link->status = DL_STATE_SUPPLIER_UNBIND call device_release_driver_internal(i2c)... device_links_busy(i2c): links->status = DL_DEV_UNBINDING __device_links_no_driver(i2c)... pinctrl--i2c link->status is DL_STATE_SUPPLIER_UNBIND oic--i2c link->status is DL_STATE_ACTIVE oic--i2c link->supplier->links.status is DL_DEV_UNBINDING The warning is triggered by the i2c removal because the OIC (supplier) links status is not DL_DEV_DRIVER_BOUND. Its links status is indeed set to DL_DEV_UNBINDING. It is perfectly legit to have the links status set to DL_DEV_UNBINDING in that case. Indeed we had started to unbind the OIC which triggered the consumer unbinding and didn't finish yet when the i2c is unbound. Avoid the warning when the supplier links status is set to DL_DEV_UNBINDING and thus support this removal sequence without any warnings.
In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: fix P2P-Device binding handling Our binding handling for P2P-Device can run into the following scenario, as observed by our testing: - a station interface is connected on some channel - the P2P-Device does a remain-on-channel (ROC) on that channel - the ROC ends, and the P2P-Device is removed from the binding, but the phy_ctxt pointer is left around as a PHY cache so we don't need to recalibrate to the channel again and again in case it's not shared - a binding update by the station interface, even a removal, will re-add the P2P-Device to the binding - the P2P-Device is removed, which removes the PHY context, but it's still in the binding so the firmware crashes Since the P2P device is removed from the binding and only re- added by unrelated code, but we want to keep the phy_ctxt around as a cache for future ROC usage, fix it by adding a boolean that indicates whether or not the P2P-Device should be added to the binding, and handle that in the binding iterator. That way, the station interface cannot re-add the P2P-Device to the binding when that isn't active.
In the Linux kernel, the following vulnerability has been resolved: cxl/region: Validate partition index before array access construct_region() reads cxled->part and uses it to index cxlds->part[] without checking for a negative value. If the partition was never resolved, part remains at its initial value of -1, causing an out-of-bounds array access. Add a guard to return -EBUSY when part is negative. The check was dropped during a merge.
In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: fix SMI event cross-process information leak kfd_smi_ev_enabled() skips the suser privilege check when pid=0. PROCESS_START, PROCESS_END, and VMFAULT events are emitted with pid=0 while carrying another process's PID and command name, so any /dev/kfd user in the render group can monitor all GPU workloads. Pass the target process PID into kfd_smi_event_add() for these events so the existing per-client filter restricts delivery to the owning process or CAP_SYS_ADMIN subscribers.
In the Linux kernel, the following vulnerability has been resolved: mm/page_owner: use memcg_data snapshot to avoid TOCTOU in print_page_owner_memcg() print_page_owner_memcg() reads page->memcg_data via READ_ONCE() at the start to guard against tail pages and NULL data. However, it later re-reads page->memcg_data locklessly in two places: 1: page_memcg_check(page) 2: PageMemcgKmem(page) (via folio_memcg_kmem(), which includes VM_BUG_ON assertions for tail pages and MEMCG_DATA_OBJEXTS) If the page is concurrently freed and reallocated as a THP tail page or slab page between these calls, the VM_BUG_ON assertions can trigger on CONFIG_DEBUG_VM=y builds, crashing the kernel. Fix both TOCTOU issues by using the memcg_data snapshot throughout.
In the Linux kernel, the following vulnerability has been resolved: pinctrl: mediatek: paris: bypass pinctrl GPIO layer in set GPIO direction pinctrl_gpio_direction_input() / pinctrl_gpio_direction_output() take the pinctrl mutex. This causes a gpiochip operations to need to sleep. Worse yet, the .can_sleep field in the gpiochip is not set. This causes the shared GPIO proxy to trip over, as it uses gpiod_cansleep() to check whether it can use a spinlock or needs a mutex. In this case, it ends up taking a spinlock, then calls pinctrl_gpio_direction_output(), which takes a mutex. This causes a huge warning. While this class of Mediatek hardware does not have separate clear/set registers, the pinctrl context has a spinlock that is taken whenever a register read-modify-write is done. Also, once the GPIO function is selected / muxed in, further GPIO operations do not involve pinctrl operations or state. The GPIO direction and level values do not require toggling the pinmux or any other pin config options. Switch to directly calling mtk_pinmux_gpio_set_direction() in the GPIO set direction callbacks to avoid taking the pinctrl mutex. Drop the .gpio_set_direction field in mtk_pmxops to signal we are no longer using the pinctrl GPIO layer for setting the direction.
In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix null pointer dereference in devcoredump cleanup In xe_devcoredump_snapshot_free(), ss->gt may be NULL when the snapshot was never fully populated (e.g., when cleanup is triggered without a prior capture). Guard the xe_guc_capture_put_matched_nodes() call with IS_ERR_OR_NULL() to prevent a null dereference. In xe_devcoredump_free(), the deferred work is only queued when a coredump is captured, so guard cancel_work_sync() with a check on coredump->captured.
In the Linux kernel, the following vulnerability has been resolved: i3c: master: svc: Prevent IRQ storm from false SLVSTART on NPCM845 On NPCM845, when a target on the I3C bus gets stuck holding SDA low, the controller reports a false Master Request (MR) in-band interrupt event. The driver handles this by emitting a STOP condition to restore the bus. However, the hardware quirk SVC_I3C_QUIRK_FALSE_SLVSTART indicates that emitting a STOP condition may spuriously set the SLVSTART interrupt status bit. In the Master Request case, this creates a feedback loop: the STOP triggers a new SLVSTART event, the IRQ handler fires again, the controller still reports an MR type, another STOP is emitted, and the cycle repeats indefinitely, resulting in an IRQ storm that can lock up the CPU. Clear the SLVSTART status bit explicitly after emitting the STOP in the Master Request IBI handler when the SVC_I3C_QUIRK_FALSE_SLVSTART quirk is set. This breaks the feedback loop without affecting normal SLVSTART processing, which is already guarded in the top-level IRQ handler by checking that MSTATUS is in SLVREQ state.
In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: avoid out-of-bounds access in monitor In NAN, we don't know on what band the frame will be sent. Therefore we set info->band to NUM_NL80211_BANDS. However, this leads to out-of-bound access in ieee80211_add_tx_radiotap_header when we try to access the sbands array. Fix it by not accessing the array if the band is NUM_NL80211_BANDS. This means that we will not report rate info for legacy rate in NAN. But nobody really cares about it.
In the Linux kernel, the following vulnerability has been resolved: genirq/proc: Size interrupt directory names for 10-digit interrupt numbers /proc/irq/<n>/ directory names are built in `char name[10]` buffers with `sprintf(name, "%u", irq)`. Ten-digit IRQ numbers already need 11 bytes including the trailing NUL, and current sparse-IRQ configurations allow interrupt numbers in that range. Size the temporary name buffer for the current decimal form and switch to bounded formatting when creating or removing the proc entry.
In the Linux kernel, the following vulnerability has been resolved: ACPICA: Enhance OEM ID and Table ID validation in acpi_ex_load_table_op() Enhance OEM ID and Table ID validation in acpi_ex_load_table_op() to prevent buffer overflows.
In the Linux kernel, the following vulnerability has been resolved: perf/ftrace: Fix WARNING in __unregister_ftrace_function perf_ftrace_function_unregister() unconditionally calls unregister_ftrace_function() without checking whether the ftrace_ops was ever successfully registered. This triggers a WARN_ON in __unregister_ftrace_function() when the ops doesn't have FTRACE_OPS_FL_ENABLED set. This can happen during perf_event_alloc() error cleanup when perf_trace_destroy() is called via __free_event() on an event whose ftrace_ops registration failed or was already torn down by perf_try_init_event()'s err_destroy path. The call path is: perf_event_alloc() error cleanup -> __free_event() -> event->destroy() [tp_perf_event_destroy] -> perf_trace_destroy() -> perf_trace_event_close() -> TRACE_REG_PERF_CLOSE -> perf_ftrace_function_unregister() -> unregister_ftrace_function() -> __unregister_ftrace_function() -> WARN_ON(!(ops->flags & FTRACE_OPS_FL_ENABLED)) Fix this by checking FTRACE_OPS_FL_ENABLED before attempting to unregister. If the ops is not enabled, just free the filter and return success.
In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Avoid DPMS-on for phantom stream [Why & How] Calling dc_update_planes_and_stream separately for stream and its phantom stream causes a NULL pointer dereference, since the phantom is destroyed on the first call. Skip the call for phantom streams.
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/pm: fix SmartShift bias sysfs store PM refcount on parse error Return the parse error before acquiring PM access.
In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: mt8365-afe-pcm: fix possible NULL-pointer dereferences in mt8365_afe_suspend() mt8365_afe_suspend() allocates the register backup buffer with devm_kcalloc(), but does not check for allocation failure before using the returned pointer. This may lead to a NULL pointer dereference when accessing afe->reg_back_up[i]. Add the missing NULL check and return -ENOMEM on allocation failure after disabling the main clock. Also propagate the return value of mt8365_afe_suspend() in mt8365_afe_dev_runtime_suspend() so that the suspended state is not updated when suspend fails.
In the Linux kernel, the following vulnerability has been resolved: netconsole: take target_cleanup_list_lock in drop_netconsole_target() drop_netconsole_target() unlinks the target while only holding target_list_lock. However, when the underlying interface has been unregistered, netconsole_netdev_event() moves the target from target_list to target_cleanup_list, and netconsole_process_cleanups_core() walks that list under target_cleanup_list_lock only. If a user removes the configfs target at the same time the cleanup worker is iterating target_cleanup_list, list_del() can corrupt the list because the two paths take disjoint locks while operating on the same list node. Acquire target_cleanup_list_lock around the list_del() so the unlink is serialised against netconsole_process_cleanups_core() regardless of which list the target currently belongs to. The state transition that downgrades STATE_DEACTIVATED to STATE_DISABLED is left intact and is performed under the same combined locking, preserving the existing ordering with resume_target().
In the Linux kernel, the following vulnerability has been resolved: spi: core: Abort active target transfer on controller suspend When an SPI controller operating in target mode has a transfer in progress at the time of system suspend, the suspend path proceeds without aborting the ongoing transfer. This can leave the hardware in an inconsistent state, potentially causing the system to hang or fail to resume cleanly. Fix this by invoking the controller's target_abort callback from spi_controller_suspend() when the controller is in target mode and the callback is registered. This ensures any active target transfer is cleanly terminated before the controller is suspended.
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: flush pending RCU callbacks on module unload Call rcu_barrier() in module exit to wait for outstanding call_rcu() callbacks before freeing module text, preventing late callback execution in freed memory. BUG: unable to handle page fault for address: ffffffffc1d59c40 PGD 6a12067 P4D 6a12067 PUD 6a14067 PMD 13698b067 PTE 0 Oops: 0010 [#1] SMP NOPTI RIP: 0010:0xffffffffc1d59c40 Code: Unable to access opcode bytes at RIP 0xffffffffc1d59c16. RSP: 0018:ffffc900198c0f28 EFLAGS: 00010286 RAX: ffffffffc1d59c40 RBX: ffff897c7d6b61c0 RCX: ffff88826aff4590 RDX: ffff8884d8b35490 RSI: ffffc900198c0f30 RDI: ffff88812af67290 RBP: 000000000000000a (DONE segment entries) R08: 0000000000000000 R09: 0000000000000100 R10: 0000000000000000 R11: ffffffff82a06100 R12: ffff88811a4e3700 R13: 0000000000000000 R14: ffff897c7d6b6270 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff897c7d680000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffc1d59c16 CR3: 00000104a980a001 CR4: 0000000002770ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <IRQ> ? rcu_do_batch+0x163/0x450 ? rcu_core+0x177/0x1c0 ? __do_softirq+0xc1/0x280 ? asm_call_irq_on_stack+0xf/0x20 </IRQ> ? do_softirq_own_stack+0x37/0x50 ? irq_exit_rcu+0xc4/0x100 ? sysvec_apic_timer_interrupt+0x36/0x80 ? asm_sysvec_apic_timer_interrupt+0x12/0x20 ? cpuidle_enter_state+0xd4/0x360 ? cpuidle_enter+0x29/0x40 ? cpuidle_idle_call+0x108/0x1a0 ? do_idle+0x77/0xf0 ? cpu_startup_entry+0x19/0x20 ? secondary_startup_64_no_verify+0xbf/0xcb (cherry picked from commit feaa5039f6c12acc9aa934c2d45dcd251a12c69f)
In the Linux kernel, the following vulnerability has been resolved: phy: renesas: phy-rcar-gen3-usb2: Fix devm action registration for disabled VBUS regulator devm_regulator_get_exclusive() initialises the regulator with enable_count = 1, requiring the consumer to disable it before release. The devm disable action was previously only registered when the caller explicitly requested enable, so when the regulator was left in its initial enabled state without an explicit enable call, the cleanup path skipped decrementing enable_count, triggering a WARN_ON during regulator release on device removal. Fix this by always registering the devm disable action based on the actual enabled state via regulator_is_enabled(), regardless of whether the caller requested an explicit enable. This covers both the explicitly enabled case and the initial state set by devm_regulator_get_exclusive().
In the Linux kernel, the following vulnerability has been resolved: bpf: Disallow interpreter fallback for BPF_ADDR_PERCPU insn The BPF_MOV64_PERCPU_REG insn requires JIT to emit native code to for 'dst_reg = src_reg + <percpu_base_off>'. However, the interpreter ignores the 'off' at its ALU64_MOV_X label. The 'off' indicates the insn is BPF_MOV64_PERCPU_REG insn. Then, when the interpreter loads memory from the register, it will hit a page fault. [ 2.545572] BUG: unable to handle page fault for address: ffffffffacaaf034 [ 2.546485] #PF: supervisor read access in kernel mode [ 2.547167] #PF: error_code(0x0000) - not-present page [ 2.547850] PGD 134e63067 P4D 134e63067 PUD 134e64063 PMD 10021c063 PTE 800ffffeca550062 [ 2.548912] Oops: Oops: 0000 [#1] SMP PTI Set jit_required as true in order to disallow interpreter fallback in core.c::__bpf_prog_select_runtime(), if any BPF_ADDR_PERCPU insn is patched to the prog. BTW, rename the helper bpf_map_supports_cpu_flags() to bpf_map_is_percpu_map().
In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Fix potential use after free in uverbs_free_dmah() When accessing a dmah via the netlink path the only synchronization mechanism for the said dmah is rdma_restrack_get(). Currently, rdma_restrack_del() is invoked at the end of uverbs_free_dmah(), which is too late, since by that point vendor-specific resources associated with the dmah might already be freed. This can leave a short window where the dmah remains accessible through restrack, leading to a potential use-after-free. Fix this by moving the rdma_restrack_begin_del() call to the start of uverbs_free_dmah(), ensuring that the dmah is removed from restrack before its internal resources are released. This guarantees that no new users hold references to a dmah that is in the process of destruction. In addition, this change preserves the intended inverted order between create and destroy routines: resources are added to restrack at the end of successful creation, and hence shall be removed from the restrack first thing during the destruction flow, which keeps the lifecycle management consistent and predictable.
In the Linux kernel, the following vulnerability has been resolved: arm64: RSI: fix field-spanning write warning in attestation token init The challenge is passed in registers a1 through a8. However, copying to ®s.a1 makes FORTIFY treat the destination as the single a1 field, resulting in a field-spanning write warning. [1] Overlay the SMCCC register structure with an RSI-specific argument layout and copy the challenge into an explicit 64-byte array. This keeps the existing a1-a8 argument encoding while giving the copy a correctly sized destination object. [1] memcpy: detected field-spanning write (size 64) of single field "®s.a1" at ./arch/arm64/include/asm/rsi_cmds.h:119 (size 8) WARNING: ./arch/arm64/include/asm/rsi_cmds.h:119 at rsi_attestation_token_init+0xdc/0xf8 [arm_cca_guest], CPU#0: cat/3314
In the Linux kernel, the following vulnerability has been resolved: clk: eswin: Zero-initialize stack-allocated clk_init_data eswin_clk_register_pll() and eswin_register_clkdiv() declare a struct clk_init_data on the stack and only initialize some of its fields (parent_data respectively parent_hws). clk_core_populate_parent_map() checks parent_names first and parent_data second before falling back to parent_hws, so leftover stack garbage in the uninitialized fields hijacks parent resolution and the clk core dereferences a bogus pointer: Unable to handle kernel NULL pointer dereference at virtual address 000000000000000c Oops [#1] epc : __clk_register+0x31a/0x7f0 [<ffffffff805dc774>] __clk_register+0x31a/0x7f0 [<ffffffff805dcd76>] devm_clk_hw_register+0x2a/0x94 [<ffffffff805e319a>] eswin_register_clkdiv+0x80/0xd0 [<ffffffff805e34a0>] eswin_clk_register_clks+0x162/0x1a0 [<ffffffff805e3736>] eic7700_clk_probe+0x146/0x180 [<ffffffff8065d23c>] platform_probe+0x3c/0x7a Observed on EIC7700 hardware (with the driver backported to a 6.17 tree); whether the bug triggers depends entirely on what the stack happens to contain when the registration helpers run. Zero-initialize both structures.